 |
Country
Default Settings
|
| Note: Some of the fields and countries are not supported
on the INTUITY AUDIX LX system. This topic was provided for reference
information. |
This topic lists the values used as default settings for various countries
for the switch tones and analog parameters. These are the values that
the INTUITY AUDIX system uses when you select and set a country on the
Switch Selection page.
To set a parameter to a different value:
- Verify that the parameter is not restricted.
If the parameter is restricted, you cannot change the value on the
INTUITY AUDIX system.
- Verify that your new setting is permitted.
Argentina
Switch Tones
The following table lists Argentina's default
settings for switch-tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
480+620 Hz
|
300 on, 600 off (2 cycles)
|
|
Ring
|
440+480 Hz
|
1500 on, 3500 off
|
|
Reorder
|
480+620 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
350+440 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Argentina's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High-Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
60
|
yes
|
|
Clipping threshold (dBm)
|
–-11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Australia
Switch Tones
The following table lists Australia's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
404+450 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
425 Hz
|
400 on, 400 off (2 cycles)
|
|
Ring
|
404+425 Hz
|
400 on, 200 off
400 on, 2000 off
|
|
Reorder
|
425 Hz
|
2500 on, 500 off
|
|
Stutter
|
404+450 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone, min 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Australia's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
1
|
no
|
|
DTMF High-Level Group (dBm)
|
–8
|
yes
|
|
DTMF Low Level Group (dBm)
|
–10
|
yes
|
|
DTMF On-time (ms)
|
60
|
yes
|
|
DTMF Off-time (ms)
|
100
|
yes
|
|
Clipping threshold (dBm)
|
–12
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–12
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
350
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Belgium
Switch Tones
The following table lists Belgium's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
425 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
425 Hz
|
500 on, 500 off (2 cycles)
|
|
Ring
|
425 Hz
|
1000 on, 3000 off
|
|
Reorder
|
425 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
—
|
—
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Belgium's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High-Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
100
|
yes
|
|
Clipping threshold (dBm)
|
–10
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–10
|
yes
|
|
CPT detect minimum (dBm)
|
–25
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Brazil
Switch Tones
The following table lists Brazil's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
425 Hz
|
950 on, 50 off
|
|
Busy
|
425 Hz
|
250 on, 250 off (2 cycles)
DISCONNECT signal
|
|
Ring
|
425 Hz
|
1000 on, 4000 off
|
|
Reorder
|
425 Hz
|
250 on, 250 off, 750 on, 250 off
|
|
Stutter
|
|
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Brazil's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High-Level Group (dBm)
|
–8
|
yes
|
|
DTMF Low Level Group (dBm)
|
–10
|
yes
|
|
DTMF On-time (ms)
|
80
|
yes
|
|
DTMF Off-time (ms)
|
80
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Canada
Switch Tones
The following table lists Canada's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
480+620 Hz
|
300 on, 600 off (2 cycles)
|
|
Ring
|
440+480 Hz
|
1500 on, 3500 off
|
|
Reorder
|
480+620 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
350+440 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Canada's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High-Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Colombia
Switch Tones
The following table lists Colombia's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
420 Hz
|
250 on, 250 off
550 on, 550 off
|
|
Ring
|
440+480 Hz
|
1500 on, 3500 off
|
|
Reorder
|
—
|
—
|
|
Stutter
|
350+440 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Colombia's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High-Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
60
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
France
Switch Tones
The following table lists France's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
440 Hz
|
Continuous, min. 2 seconds
|
|
Busy
|
440 Hz
|
500 on, 500 off (2 cycles)
|
|
Ring
|
440 Hz
|
1500 on, 3500 off
|
|
Reorder
|
440 Hz
|
200 on, 200 off (2 cycles)
|
|
Stutter
|
—
|
—
|
|
First additional
|
330 Hz
|
Continuous, min. 2 seconds; report as "dial"
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists France's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High-Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Germany
Switch Tones
The following table lists Germany's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
425 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
425 Hz
|
150 on, 475 off (2 cycles)
|
|
Ring
|
425 Hz
|
1000 on, 4000 off
|
|
Reorder
|
425 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
425 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Germany's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
100
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–11
|
yes
|
|
CPT detect minimum (dBm)
|
–25
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Greece
Switch Tones
The following table lists Greece's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
480+620 Hz
|
500 on, 500 off (2 cycles)
|
|
Ring
|
440+480 Hz
|
1000 on, 3000 off
|
|
Reorder
|
480+620 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
350+440 Hz
|
125 on, 125 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
350+440 Hz
|
125 on, 125 off followed by continuous tone
of min. 1.5 seconds; report as "dial"
|
|
Second additional
|
350+440 Hz
|
125 on, 125 off (2 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Greece's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Hong Kong
Switch Tones
The following table lists Hong Kong's default
settings for switch tones:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Analog Parameters
The following table lists Hong Kong's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
India
Switch Tones
The following table lists India's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
480+620 Hz
|
300 on, 600 off (2 cycles)
|
|
Ring
|
440+480 Hz
|
1500 on, 3500 off
|
|
Reorder
|
480+620 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
350+440 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists India's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low-Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
60
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Japan
Switch Tones
The following table lists Japan's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
404 Hz
|
Continuous, min. 2 seconds
|
|
Busy
|
404 Hz
|
500 on, 500 off (2 cycles)
|
|
Ring
|
375+425 Hz
|
1250 on, 2500 off
|
|
Reorder
|
—
|
—
|
|
Stutter
|
404 Hz
|
100 on, 100 off (3 cycles) followed by 250
on, 250 off
|
|
First additional
|
404 Hz
|
250 on, 250 off (2 cycles); report as "dial"
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Japan's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–10.2
|
yes
|
|
DTMF Low Level Group (dBm)
|
–11.2
|
yes
|
|
DTMF On-time (ms)
|
80
|
yes
|
|
DTMF Off-time (ms)
|
80
|
yes
|
|
Clipping threshold (dBm)
|
–16
|
yes
|
|
Clipping duration (ms)
|
1000
|
yes
|
|
Clipping limit (dBm)
|
–16
|
yes
|
|
CPT detect minimum (dBm)
|
–30
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Luxembourg
Switch Tones
The following table lists Luxembourg's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
425 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
425 Hz
|
500 on, 500 off (2 cycles)
|
|
Ring
|
425 Hz
|
1000 on, 3000 off
|
|
Reorder
|
425 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
—
|
—
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Luxembourg's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
100
|
yes
|
|
Clipping threshold (dBm)
|
–10
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–10
|
yes
|
|
CPT detect minimum (dBm)
|
–25
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Mexico
Switch Tones
The following table lists Mexico's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+425 Hz
|
Continuous, min. 2 seconds
|
|
Busy
|
350+425 Hz
|
250 on, 250 off (2 cycles)
|
|
Ring
|
425 Hz
|
1000 on, 4500 off
|
|
Reorder
|
—
|
—
|
|
Stutter
|
350+425 Hz
|
100 on, 100 off (3 cycles), followed by continuous
tone of min. 2 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Mexico's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
80
|
yes
|
|
DTMF Off-time (ms)
|
80
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
The Netherlands
Switch Tones
The following table lists the Netherlands' default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
425 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
425 Hz
|
500 on, 500 off (2 cycles)
|
|
Ring
|
425 Hz
|
1000 on, 3500 off
|
|
Reorder
|
425 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
—
|
—
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists the Netherlands' default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–8.7
|
yes
|
|
DTMF Low Level Group (dBm)
|
–10.7
|
yes
|
|
DTMF On-time (ms)
|
100
|
yes
|
|
DTMF Off-time (ms)
|
100
|
yes
|
|
Clipping threshold (dBm)
|
–11.5
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–11.5
|
yes
|
|
CPT detect minimum (dBm)
|
–25
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
New Zealand
Switch Tones
The following table lists New Zealand's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
404+450 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
425 Hz
|
400 on, 400 off (2 cycles)
|
|
Ring
|
404+425 Hz
|
400 on, 200 off, 400 on, 2000 off
|
|
Reorder
|
425 Hz
|
2500 on, 500 off
|
|
Stutter
|
404+450 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone, min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists New Zealand's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
1
|
no
|
|
DTMF High Level Group (dBm)
|
–8
|
yes
|
|
DTMF Low Level Group (dBm)
|
–10
|
yes
|
|
DTMF On-time (ms)
|
60
|
yes
|
|
DTMF Off-time (ms)
|
100
|
yes
|
|
Clipping threshold (dBm)
|
–12
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–12
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
350
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Singapore
Switch Tones
The following table lists Singapore's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
404+450 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
404 Hz
|
400 on, 400 off (2 cycles)
|
|
Ring
|
404+425 Hz
|
250 on, 250 off, 250 on, 2000 off
|
|
Reorder
|
404+425 Hz
|
2500 on, 500 off
|
|
Stutter
|
404+450 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
404+450 Hz
|
150 on, 150 off followed by continuous tone
of min. 1.5 seconds
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Singapore's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
80
|
yes
|
|
DTMF Off-time (ms)
|
80
|
yes
|
|
Clipping threshold (dBm)
|
–10
|
yes
|
|
Clipping duration (ms)
|
750
|
yes
|
|
Clipping limit (dBm)
|
–10
|
yes
|
|
CPT detect minimum (dBm)
|
–30
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Spain
Switch Tones
The following table lists Spain's default settings
for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
425 Hz
|
Continuous, min. 2.5 seconds
|
|
Busy
|
425 Hz
|
200 on, 200 off (2 cycles)
|
|
Ring
|
425 Hz
|
1500 on, 3000 off
|
|
Reorder
|
425 Hz
|
200 on, 200 off (2 cycles) followed by 200
on, 600 off
|
|
Stutter
|
425 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 2.5 seconds
|
|
First additional
|
425 Hz
|
150 on, 150 off (2 cycles) followed by continuous
tone of min. 2.5 seconds; report as "stutter"
|
|
Second additional
|
425 Hz
|
150 on, 150 off followed by continuous tone
of min. 2.5 seconds; report as "dial"
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Spain's default settings
for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
80
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–10
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–10
|
yes
|
|
CPT detect minimum (dBm)
|
–25
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Thailand
Switch Tones
The following table lists Thailand's default
settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
480+620 Hz
|
300 on, 600 off (2 cycles)
|
|
Ring
|
440+480 Hz
|
1500 on, 3500 off
|
|
Reorder
|
480+620 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
350+440 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists Thailand's default
settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
United Kingdom
Switch Tones
The following table lists the United Kingdom's
default settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
404 Hz
|
375 on, 375 off (2 cycles)
|
|
Ring
|
404+450 Hz
|
400 on, 200 off, 400 on, 2000 off
|
|
Reorder
|
404 Hz
|
400 on, 350 off, 225 on, 525 of
400 on, 350 off, 225 on, 525 off
|
|
Stutter
|
350+440 Hz
|
100 on, 100 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists the United Kingdom's
default settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–11
|
yes
|
|
DTMF Low Level Group (dBm)
|
–13
|
yes
|
|
DTMF On-time (ms)
|
80
|
yes
|
|
DTMF Off-time (ms)
|
80
|
yes
|
|
Clipping threshold (dBm)
|
–13
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–9
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
80
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
United States
Switch Tones
The following table lists the United States'
default settings for switch tones:
|
Tone
|
Frequency
|
Description
|
|
Dial
|
350+440 Hz
|
Continuous, min. 1.5 seconds
|
|
Busy
|
480+620 Hz
|
300 on, 600 off (2 cycles)
|
|
Ring
|
440+480 Hz
|
1500 on, 3500 off
|
|
Reorder
|
480+620 Hz
|
250 on, 250 off (2 cycles)
|
|
Stutter
|
350+440 Hz
|
150 on, 150 off (3 cycles) followed by continuous
tone of min. 1.5 seconds
|
|
First additional
|
—
|
—
|
|
Second additional
|
—
|
—
|
|
Third additional
|
—
|
—
|
Analog Parameters
The following table lists the United States'
default settings for analog parameters:
|
Parameter
|
Default Value
|
Restricted?
|
|
Answer delay (rings)
|
0
|
no
|
|
DTMF High Level Group (dBm)
|
–6
|
yes
|
|
DTMF Low Level Group (dBm)
|
–8
|
yes
|
|
DTMF On-time (ms)
|
360
|
yes
|
|
DTMF Off-time (ms)
|
160
|
yes
|
|
Clipping threshold (dBm)
|
–11
|
yes
|
|
Clipping duration (ms)
|
500
|
yes
|
|
Clipping limit (dBm)
|
–8.8
|
yes
|
|
CPT detect minimum (dBm)
|
–35
|
yes
|
|
Energy detect minimum (dBm)
|
–38
|
yes
|
|
Post onhook delay (ms)
|
2000
|
no
|
|
Post offhook delay (ms)
|
1500
|
no
|
|
Wink duration (ms)
|
300
|
no
|
|
Input volume
|
4000
|
no
|
|
Output volume
|
1000
|
no
|
Top of page
|
