Uniform Dial Plan Features

System Programming

Specifying New Extension Ranges
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	None
Planning Form	2a, System Numbering: Extension Jacks 2b, System Numbering: Digital Adjuncts 2d, System Numbering: Special Renumbers Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	Not applicable
Valid Entries	Starting and ending numbers for old and new extension ranges. When entering the first and last extension in UDP extension ranges, enter the full number of digits specified by the dial plan selected (two, three, or four digits).
Ranges	50
Inspect	Yes, existing number ranges
Copy Option	No
Procedure	Assign extension number ranges for non-local dial plan extensions: SysRenumberNonLocal UDPDial no. of first extension in rangeEnterDial no. of last extension in rangeEnter Dial max. no. of digits user can enter to reach an extension in the range (1-11)EnterDial no. of pattern for extension range → EnterBackBack
Deleting Extension Ranges
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	None
Planning Form	2a, System Numbering: Extension Jacks 2b, System Numbering: Digital Adjuncts 2d, System Numbering: Special Renumbers Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	Not applicable
Valid Entries	Starting numbers for extension ranges to be deleted
Inspect	Yes: existing number ranges
Copy Option	No
Procedure	Delete extension number ranges for non-local dial plan extensions: SysRenumberNonLocal UDPDial no. of first extension in rangeEnterDelRangeBackBack
UDP Pool Routing
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	Not required
Planning Form	Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	Not applicable
Valid Entries	Routes (1-4)
Inspect	Yes
Copy Option	No
Procedure	Specify UDP routes: TablesUDP RoutingDial pattern no. (1-20)Enter Dial route no. (1-4)EnterPoolDial pool dial-out code (up to 4 digits)EnterBackBackBackBack
UDP Route Facility Restriction Level
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	Not required
Planning Form	Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	3
Valid Entries	0 to 6
Inspect	No
Copy Option	No
Procedure	Specify FRLs for UDP routes: TablesUDP RoutingDial pattern no. (1-20)Enter Dial route no. (1-4)EnterFRLDial restriction level (0-6) EnterBackBackBackBack
UDP Digit Absorption
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	Not required
Planning Form	Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	0
Valid Entries	0 to 11
Inspect	No
Copy Option	No
Procedure	Specify how many dialed digits should be absorbed (not sent over the trunk) by the system when a UDP call to a non-local extension is made on an identified UDP route: TablesUDP RoutingDial pattern no. (1-20)Enter Dial route no. (1-4)EnterAbsorbDrop Dial number of absorption digits (0-11)EnterBackBack BackBack
UDP Other Digits
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	Not required
Planning Form	Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	0
Valid Entries	Up to 20 digits (any combination of 0 to 9)
Inspect	No
Copy Option	No
Procedure	Specify other (extra) digits that must be added by the system to the beginning of the dialed digits when calls are placed on an identified UDP route: TablesUDP RoutingDial pattern no. (1-20)Enter Dial route no. (1-4)EnterDigitsDrop Dial digits to add (up to 20; any combination of 0-9)Enter BackBackBackBack
UDP Voice and/or Data Routing
Programmable by	System Manager
Mode	Hybrid/PBX
Idle Condition	Not required
Planning Form	Non-Local Dial Plan Administration Form in the Installation Specification
Factory Setting	Voice/Data
Valid Entries	Voice Only, Data Only, Voice/Data
Inspect	No
Copy Option	No
Procedure	Specify voice, data, or both for an identified UDP route (use for routes with pools of PRI or T1 facilities): TablesUDP RoutingDial pattern no.Enter Dial route no.EnterDataSelect capability (Voice Only, Data Only, Voice/Data)EnterBackBackBackBack
SMDR UDP Calls Recorded on Call Report
Programmable by	System Manager
Mode	All
Idle Condition	Not required
Planning Form	8a, System Features
Factory Setting	Log Incoming/Outgoing
Valid Entries	Log Incoming/Outgoing, Log None
Inspect	No
Copy Option	No
Procedure	When SMDR is set to record both incoming and outgoing calls, specify how private networked trunk calls should be recorded: OptionsSMDRUDPSelect Log Incoming/Outgoing or Log NoneEnterBackBack

Topics

Description

Intersystem Calling

	Extension Ranges
	Call Handling for Non-Local Dial Plan Extensions

At a Glance

Considerations & Constraints

System Programming

Telephone Differences

Feature Interactions