|
Use the Add New Machine: AMIS Analog page to add
a new AMIS Analog remote machine to the Message Networking system
or to modify an existing machine.
This page contains the following fields.
New Machine Name: Type a unique name for
the remote machine you are adding. The machine name can be up to 23 alphanumeric
characters:
- Enter uppercase letters as uppercase.
- Enter lowercase letters as lowercase.
- Use a hyphen (-) or an underscore (_).
- These names cannot start with a number.
- There can be no blank spaces.
Note: The name must be unique on both the local Message Networking
network as well as any other Message Networking systems in the network. To ensure
that you are using a unique name, check the
Remote Machines List on all Message Networking systems in your network.
Machine Type: Select AMIS
Analog.
Dial String: Type the gateway telephone
number of the remote machine, up to 30 characters. The Message Networking
system uses the dial string to contact and send messages to the
remote machine. The dial string typically consists of the dial-access
code needed to reach the network, followed by a pause interval,
followed by the telephone number of the remote machine.
Note: You can make the Message Networking system pause
for a specific length of time by entering "P" (including
quotes) in the dial string. A single "P" causes the system
to pause approximately 1.5 seconds; a "P" followed by
a digit from 1 to 9 causes the system to wait the specified number
of seconds.
Mailbox ID Length: Type the number of digits
in mailbox IDs on the remote machine, up to 10 digits.
Default Language: Specify the default language
on the remote machine.
Failed Msg. Notification Priority?: Indicates
whether to mark failed message notifications with priority status. Select yes
to mark failed message notifications with priority status. Select no
if you do not want to mark failed message notifications with priority status.
The default for this field is no.
Msg ID?: Specify whether to include the original
message ID in failed message notifications. Select yes to include the
original message ID. Select no if you do not want to include the original
message ID in failed message notifications. The default for this field is no.
Send Message for EAW?: Specify whether the original
message is sent back to a subscriber after that subscriber has sent a message
from this machine to an Aria machine that has the Extended Absence Greeting
(EAG) warning activated. This message return is in addition to the message indicating
the actual EAG warning condition. Select yes to return the original message.
Select no if you do not want to return the original message. The default
for this field is no.
Default NameNet Type: Specify the default NameNet
type, set up on the remote machine, that is used for aging purposes by the remote
machine. Type p if directory entries are permanent. Type u if
entries are usage-based, which indicates that directory entries are temporarily
available based on the network traffic of a particular remote machine. The default
for this field is u.
Organization: Use this field to provide a description
of the organization using Message Networking, up to 64 characters. This field
is optional and for informational purposes only.
Organization Unit: Use this field to provide a description
of the organization unit using Message Networking, up to 64 characters. This field
is optional and for informational purposes only.
Node ID: Unique node ID for this remote
machine. This field is display-only and cannot be modified.
Comments: You can optionally type
any comments about this remote machine, up to 68 alphanumeric characters.
Allow Private Messages?: Indicates whether
to allow private messages to be sent to the AMIS subscriber. y or n Default
- n
Caution: If set to y, subscribers
can forward a private message they have received.
Include Voice Name of Sender?: Indicates whether
to include the sender's voice name with the message. y or n Default - n
Include Message Marking (Private/Priority)?:
Indicates whether to include a private or priority marking with a message. y
or n Default - n
Default Community ID: Community identifier for
all subscribers added to this remote machine. An integer of 1 through 15.
Maximum Simultaneous Connections: Maximum number
of ports that will simultaneously handle outgoing traffic for this machine.
Enter an integer of 1 through 9 The default for this field is 1.
Timing
Type: Select the appropriate AMIS timing type for the remote machine
you are defining from the drop-down list. You can use the AMIS Timing
Parameters page to add, modify,
and delete AMIS timing parameters.
Message Networking Callback Number:
Identifies the Message Networking system to this remote machine
and is used for protocol exchanges with AMIS Analog remote machines.
The defaults for these fields are provided by the AMIS Analog Parameters
page, but you can modify the fields to use different numbers.
- Country Code: Identifies the unique country code that
helps identify the Message Networking system to this remote machine.
Enter 1 to 4 digits.
- Area/Trunk: Identifies the unique area code or trunk
that helps identify the Message Networking system to this remote
machine. Enter 1 to 6 digits.
- Telephone Number: Identifies the unique telephone number
that helps identify the Message Networking system to this remote
machine. Enter 1 to 10 digits.
Remote Machine ID: Identifies
this remote machine:
- Country Code: Identifies the
unique country code that helps identify the remote machine. Enter
1 to 4 digits.
- Area/Trunk: Identifies the unique
area code or trunk that helps identify the remote machine. Enter
1 to 6 digits.
- Telephone Number: Identifies the
unique telephone number that helps identify the remote machine.
Enter 1 to 10 digits.
If you are modifying an existing machine, click Save to
save your changes. If you are adding a new machine, click Next
Step to save the remote machine and administer
dial plan mapping, or click Add this Machine if you do
not want to administer dial plan mapping at this time:
- If you click Next Step, the Administer Dial Plan Mapping
page displays.
- If you click Add this Machine, a message displays that
the parameters have been saved. Click OK.
Top of page
|
