Share this worksheet with the LAN administrator. Default values are shown in braces.
The administrator may require you to change IP addresses to prevent conflicts with existing endpoints on the corporate LAN. Make precise notes of any changes and follow instructions exactly.
Allow up to 4 hours to complete this worksheet. This will speed up server configuration, and could prevent you from losing work in progress.
It is crucial to coordinate the IP addresses that will
be used with your Avaya media server with those on the corporate LAN.
If you specify an Ethernet address for the Avaya server component that
conflicts with another Ethernet endpoint, the resulting problems with
traffic on the local area network may be extremely difficult to diagnose
and solve.
For more information, see the guide: Preinstallation Network Worksheet S8700 IP Connect
The worksheet items are arranged in the order in which they are needed during server configuration. For an illustration of these items, see IP Connect duplex configuration.
Server number 1 & 2 must be on the same subnet (be sure to configure both servers)
Server names (these should also be administered on any relevant corporate DNS servers)
Name of server 1: __________________________________
Name of server 2: __________________________________
Active server name: __________________________________
Ethernet interface functions (the corporate LAN function may be assigned to Ethernet 4 if the IP-configuration uses a private LAN for its control network)
Function assigned to Ethernet 0: {control network A plus the corporate LAN, if a private control network is not used} _____________________
Function assigned to Ethernet 1: {services laptop} _____________________
Function assigned to Ethernet 2: {duplication link} _____________________
Function assigned to Ethernet 4: {corporate LAN, if a private control network is used} _____________________
Ethernet 0 default addresses (for control network A plus the corporate LAN if a private control network is not used):
Server 1 IP address on control network A/corporate LAN: {198.152.254.201} _____________________
Server 2 IP address on control network A/corporate LAN: {198.152.254.202} _____________________
Active server IP address on control network A/corporate LAN: {198.152.254.200} _____________________
Gateway IP address for control network A/corporate LAN: _____________________
Subnet mask for control network A/corporate LAN: {255.255.255.0} _____________________
Speed of link (10 or 100 megabit, full or half duplex): {autosense} _____________________
VLAN 802.1q priority tagging: {off} _____________________
Ethernet 2 default addresses (for duplication link):
Server 1 IP address on duplication link: {192.11.13.13} _____________________
Server 2 IP address on duplication link: {192.11.13.14} _____________________
Subnet mask for the duplication link: {255.255.255.252} _____________________
Speed of link (100 megabit, full duplex): {autosense} _____________________
Ethernet 3 (in default configuration, not used).
Ethernet 4 addresses (for corporate LAN if a private control network is used, no default values):
Server 1 IP address on the corporate LAN: _____________________
Server 2 IP address on the corporate LAN: _____________________
Active server IP address on the corporate LAN: _____________________
Gateway IP address for the corporate LAN: _____________________
Subnet mask for the corporate LAN: _____________________
Speed of link (10 or 100 megabit, full or half duplex): {autosense} _____________________
VLAN 802.1q priority tagging: {off} _____________________
Ethernet 1 addresses are fixed for the services (laptop)
interface:
IP address for every Avaya media server: 192.11.13.6
Subnet mask for the laptop link: 255.255.255.252
Specify the Ethernet switches (two may be used for a large number of port networks)
Number of Ethernet switches: {1} _____
Ethernet switch 1 IP address: {198.152.254.240} _____________________
SNMP GET (read) community string: {public} _____________________
SNMP SET (write) community string: _____________________
Ethernet switch 2 IP address: {198.152.254.241} _____________________
SNMP GET (read) community string: {public} _____________________
SNMP SET (write) community string: _____________________
If Ethernet switches are part of the switch configuration
and report alarms to the media servers using SNMP, they must be on the
same subnet as the media servers.
Specify the UPS units for the server
Number of UPS units: {2} _____
UPS 1 IP address: {198.152.254.239} _____________________
SNMP GET (read) community string: {public} _____________________
SNMP SET (write) community string: _____________________
UPS 2 IP address: {198.152.254.238} _____________________
SNMP GET (read) community string: {public} _____________________
SNMP SET (write) community string: _____________________
The UPS units must be on the
same subnet as the media servers, and must report alarms through SNMP
to the servers in order for the servers to respond correctly to a loss
of power.
Optional: If domain name service (DNS) servers are to be used, complete as many of the following fields as needed to set up DNS service and limit unresolved name searching. Fill out only as many server and search domain fields as are needed:
DNS server 1 IP address: _____________________
DNS server 2 IP address: _____________________
DNS server 3 IP address: _____________________
DNS domain name: _____________________
Search domain name 1: _____________________
Search domain name 2: _____________________
Search domain name 3: _____________________
Search domain name 4: _____________________
Search domain name 5: _____________________
DHCP service is not currently available for S8700 IP Connect.
Optional: Enter any static IP addresses required to ensure delivery of information over certain parts of the network.
|
IP address of endpoint server is trying to reach |
Subnet mask used by all endpoints |
Gateway IP address (optional) |
Ethernet interface |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Is a Network Time Server (NTS) available to be used as the time source? (y/n) _____
If NTSs are available, enter their DNS name or IP address (up to 3, in preferred order)
Primary NTS name or IP address: _____________________
Secondary NTS name or IP address: _____________________
Tertiary NTS name or IP address: _____________________
Should the server support NTSs that multicast timing messages? (y/n): _____
Enter any valid key numbers supplied by the LAN administrator (otherwise leave blank)
Trusted Key: _____________________
Request Key: _____________________
Control Key: _____________________
Provide the location or content of the keys file (if used): _____________________
Specify the IP address for each server's modem (this information must be provided by Avaya Services if a maintenance contract is in force):
IP address of the PPP dial-up link for server 1: _____________________
IP address of the PPP dial-up link for server 2: _____________________
Use the default return routes provided by Services (unless specifically instructed to change them).
Specify Simple Network Management Protocol (SNMP) alarming information for each trap destination (needed only if a corporate network management system is in use)
IP address of SNMP trap destination: _____________________
SNMP protocol version (1, 2c or 3): _____
Required for version 1:
Community name: _____________________
Required for version 2c:
Notification type (trap/inform): _____________________
Community name: _____________________
Required for version 3:
Notification type (trap/inform): _____________________
User name: _____________________
Security model (none, authentication, or privacy): _____________________
Authentication password (required for authentication and privacy model): _____________________
Privacy password (required for privacy model): _____________________
S8700 IP Connect duplex configuration
S8700 Multi-Connect duplex configuration