Avaya Support Forums  

Go Back   Avaya Support Forums > Small and Medium Business Communications

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 03-20-2017, 03:31 AM
dmgelgar dmgelgar is offline
Member
 
Join Date: Dec 2016
Location: Kyiv, Ukraine
Posts: 4
dmgelgar has 10 reputation points
Default IP Office SCN - no voice calls

There is a network of IP Offices connected via H.323 trunks. Some of them are IPO SOE R4.2.3, three of them are IPO 500, one runs R8.1, two run R9.0. VoIP calls goes fine, dialling plan is built up, extention numbers and Line IDs are unique.
I try to run SCN between these two IPO500 R9.0 . As soon as I change Supplementary Services field in line administration form to "IP Office SCN" (on both PBXs) vioce calls between these two sites are stopped.
On both sides System Status app shows the line state SCN is Up, in Resourses/Directory the neighbor' extentions are shown as got via SCN from 192.168.X.X , in Monitor app on site A - I can see that it does not use any short code to route the call - it knows it should use SCN trunk to set up the call - it sends setup and then drops with reason - Network out of order. On the site B the Monitor app shows no call setup try at all. These sites are connected via VPN, network admin says there is no port restriction.
Where sould I look for a resolution?
+++++++++++++ Site A ++++++++++++++++++++++++++++++++++++++++++++++
17:20:14 443671mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: CancelTimer CMTCDelayedProcessing
17:20:14 443671mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: LOOKUP CALL ROUTE: type=100 called_party=705 sub= calling=122 dir=out complete=0 ses=0
17:20:14 443671mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: ADD TARGET (N): number=705 type=100 depth=1 nobar=1 setorig=1 ses=0
17:20:14 443671mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: SET USER: A705 orig=1
17:20:14 443672mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: ADD USER: A705 depth=1 disallow_cw=0 dnd=0 real_call=1 group_call=0 type(CMNTypeDefault) incl(0x0) excpt(0x0), allow_redir(0) remote=c0a80c7d simult 0 (0)
17:20:14 443672mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: Direct to Remote Target: A705
17:20:14 443672mS CMTARGET: 0.1003.0 1 AvayaPreSale122.0: MakeCallToNetworkedUser A705 simult:0 ipad=192.168.12.125 via 192.168.12.125
17:20:14443673mS CMCallEvt:0.1005.0 -1 BaseEP: NEW CMEndpoint f4dc5c98 TOTAL NOW=3 CALL_LIST=1
17:20:14 443675mS CMTARGET: MakeCallToNetworkedPBX using line group id: 76140 ipaddr=192.168.12.125
<...>
17:20:14 443683mS H323Evt: v=0 stacknum=24 State, new=NullState, old=NullState id=-1
17:20:14 443686mS H323Evt: v=0 stacknum=24 State, new=Initiated, old=NullState id=1005
17:20:14 443687mS H323Tx: 2 dst=192.168.12.125:1720
H323 Pcol=08(Q931) Reflen=2 ref=0001(Remote)
Message Type = Setup
ForwardLCParameters [G711_ALAW64K (frames=20)] H2250 SID=01: RTP=192.168.0.131(49152) , RTCP=192.168.0.131(49153) ,
<...>
ReverseLCParameters G7231 H2250 SID=01: RTP=192.168.0.131(49152) , RTCP=192.168.0.131(49153) ,

17:20:15 444176mS SCN Ctrl Tx: PropagateBLF to 192.168.12.125 length=40
17:20:15 444176mS VPN TFTP Tx: v=192.168.12.125
AVCONTROL (3) TFTP DATA (3) seqnum = 20
controltype BLF (2)
17:20:15 444184mS VPN TFTP Rx: v=192.168.12.125
AVCONTROL (3) TFTP ACK (4) seqnum = 20
17:20:17 446575mS AVRIP Rx: v=192.168.12.125 send=0 receive=0
PLATFORM: voice=00006033 ipad=0.0.0.0 operational 1 version 3 recordsupported 1
Platform Id 0 Version 9.0(2148271086)
Name SecNet-IPO500
Codepage 2, Unicode UnicodeSupportOn
Time offset: 0
17:20:17446576mS VPNR: AVRIP receive from pbx 192.168.12.125 count = 0
17:20:17446576mS VPNR: AVRIPRX VPNN_RIP_PLATFORM_INFO => node IP: 192.168.12.125, tunnel IP: 0.0.0.0
17:20:18 447687mS H323Tx: 2 dst=192.168.12.125:1720
H323 Pcol=08(Q931) Reflen=2 ref=0001(Remote)
Message Type = ReleaseComplete

17:20:18 447687mS H323Evt: v=0 stacknum=24 State, new=NullState, old=Initiated id=1005
17:20:18447688mS CMCallPkt: v=0
CMReleaseComp
Line: type=IPLine 24 Call: lid=0 id=1005 in=0
Cause=38, Network out of order
+++++++++++++ Site B ++++++++++++++++++++++++++++++++++++++++
17:20:15 405242mS VPN TFTP Rx: v=192.168.0.131
AVCONTROL (3) TFTP DATA (3) seqnum = 18
controltype BLF (2)
0000 02 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0010 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
0020 00 00 00 00 00 12 00 09 ........
17:20:15 405242mS VPN TFTP Tx: v=192.168.0.131
AVCONTROL (3) TFTP ACK (4) seqnum = 18
17:20:15 405242mS SCN Ctrl Rx: ParseRemoteBLF from 192.168.0.131 Array Length(39)
Reply With Quote
  #2  
Old 03-20-2017, 03:37 PM
thiel2 thiel2 is offline
Genius
 
Join Date: Apr 2013
Posts: 340
thiel2 has 50 to 99 reputation pointsthiel2 has 50 to 99 reputation pointsthiel2 has 50 to 99 reputation pointsthiel2 has 50 to 99 reputation points
Default

Your releases are very far apart, only 1 major release between sites is supported. However, go to the VoIP tab for each SCN line and uncheck Allow Direct Media Path and see if that restores voice.
Reply With Quote
  #3  
Old 03-21-2017, 04:48 AM
dmgelgar dmgelgar is offline
Member
 
Join Date: Dec 2016
Location: Kyiv, Ukraine
Posts: 4
dmgelgar has 10 reputation points
Default

Quote:
Originally Posted by thiel2 View Post
Your releases are very far apart, only 1 major release between sites is supported. However, go to the VoIP tab for each SCN line and uncheck Allow Direct Media Path and see if that restores voice.
BTW, I tried to use SCN feature between R9.0 and R4.2.3 (Voice Networking feature on Line administration form in R4.2) - it worked pretty normal - voice calls, BLF of networked PBX' user, etc.
But now I'm trying to set up SCN between two IPO500 with identical software release - up to date R9.0(12) .
Without SCN feature the trunk works fine with and without Direct Media Pass.
Reply With Quote
Reply

Tags
ip office, scn

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 03:24 AM.

This Forum is provided solely for the use and convenience of Avaya customers and partners. Use of the Forum is subject to the Terms and Use and Privacy Statement found at www.avaya.com. No other use is permitted. The Forum including all content posted is “AS IS” and Avaya expressly disclaims all warranties and/or guarantees as to its accuracy, reliability, usefulness, quality or non-infringement of intellectual property. Avaya reserves the right to remove any content posted on the Forum at any time and for whatever reason.

Avaya will not be liable for any content posted on this Forum, including, without limitation, any errors or omissions or for any losses or damages of any kind incurred as a result of use or reliance on any content, regardless of its origin.

You expressly understand and agree that you assume all risks associated with use or reliance on this content.