Removing the Front Panel

To remove the front panel from the MAP/5:

1. Disconnect the power cable.
2. Disconnect the keyboard cable.
3. Place the system on its side panel. The bottom of the unit needs to be facing toward you. The front panel latches must also be facing toward you.
4. Slide the drive cover to the center to expose both front panel latches.

The latches are on the bottom of the front panel.


 


Tip: The front panel is flexible enough for you first to press one latch and then the other.

5. Push inward on the two front panel latches to release the bottom edge of the front panel. See Front Panel Tabs.
6. When the bottom of the front panel is loose, rotate the panel away from you and lift it to remove.
7. Return the unit to its flat, desktop position.

Removing the Top Cover

Observe proper electrostatic discharge precautions when you handle computer components. Wear an antistatic wrist strap that touches your bare skin and connect the strap cable to an earth ground. For detailed electrostatic discharge instructions, see Protecting Against ESD Damage on the Intuity Messaging Solutions Release 5 Documentation for Technicians CD-ROM, 585-313-807.

To remove the top cover of the MAP/5 for access to the SCSI connection:

1. Press the top cover holding tabs outward while pushing the top cover away from you.

These holding tabs are located on either side of the front of the unit.

2. Slide the top cover as far back as it will go, which is about 0.5 inches.
3. Lift the top cover straight up to remove.
4. Reconnect the keyboard cable and the power cable.
    
   

   Note: Do not turn on the MAP/5 system power.

Assembling and Attaching the External Disk Cartridge Drive

The following procedure describes how to assemble and attach a JAZ or a Magneto-Optical (MO) disk cartridge drive to the old system.

To assemble and attach the external disk cartridge drive to the old system:

1. Remove the external disk cartridge drive from the Reusable Upgrade Kit (RUK).
2. Do one of the following:
• If the RUK contains an External JAZ Disk Cartridge Drive:
• Set the SCSI ID to 5. Use a pointed tool to increase or decrease the SCSI ID by clicking the + or – switches. See External JAZ Disk Cartridge Drive Settings.
• Confirm that the termination switch is set to 1, which is pushed to the left side. This might require the use of a flashlight. See External JAZ Disk Cartridge Drive Settings for more information.
• Turn off the external drive power switch by setting the power switch to 0 or off. This switch is located at the back right side of the drive.
• Continue with Step�3.
• If the RUK contains an External Magneto-Optical (MO) Disk Cartridge Drive:
• Set the SCSI ID to 4 by turning the SCSI ID setting arrow to point to 4. See External Magneto-Optical (MO) Disk Cartridge Drive Settings for more information.
• Set the four Option Settings to On. See External Magneto-Optical (MO) Disk Cartridge Drive Settings.
• Turn off the external disk cartridge drive's power switch. This switch is located at the back of the drive in the upper left corner. See the External Magneto-Optical (MO) Disk Cartridge Drive Settings.
• Continue with Step�3.
3. Check the back of the MAP/5 for an external SCSI connection:
• If the system has an external SCSI connection, plug the SCSI cable to the connector on the back of the system and then go to Step 8 on page 3.
• If the system does not have an external SCSI connection, continue with Step 4.
4. Remove the 1-foot cable and adapter from the RUK.
5. Connect the 1-foot cable to the adapter. See 1-foot Cable and Adapter.
6. Inside the MAP/5, connect the adapter to a free connection on the MAP/5 SCSI ribbon cable.

See either Connecting the SCSI Cable, Adapter, and 1-foot Cable (JAZ disk cartridge drive) or Connecting the SCSI Cable, Adapter, and 1-foot Cable (MO disk cartridge drive), depending on the disk cartridge drive type.

7. Ensure that:
• The internal SCSI cable is pulled up and away from any of the circuit cards and that it will stay in this position during the backup.
• The metal pins on the back of the adapter do not touch any metal parts of the cabinet.
8. Connect the other end of the SCSI cable to the upper connector on the back of the external disk cartridge drive.


 


Do not use the lower connector or the backup might not occur.

9. Place the external disk cartridge drive on a stable surface.
10. Connect the external drive to electrical power.
11. Do one of the following:
• If you are using a JAZ disk cartridge drive, turn on the external disk cartridge drive power switch by setting the power switch to the 1 position.
• If you are using a MO disk cartridge drive, turn on the external disk cartridge drive power switch. This switch is located at the back of the drive in the upper left corner.


 


Note: Do not turn on the MAP/5 system power.

12. Insert one of the disk cartridges from the RUK in the disk cartridge drive. See JAZ Disk Cartridge or Magneto-Optical (MO) Disk Cartridge.
13. Confirm that the SCSI ribbon cable inside the MAP/5 is connected to the hard disk drive.


 


Important! The SCSI ribbon cable disconnects from the hard disk drive easily. If the cable is loose, the system must be shut down again to reconnect the cable.

http://www.avaya.com Avaya UCS Information Development