Users Affected
Telephone users, operators, data users
Reports Affected
DS1 Information, PRI Information, SMDR
Modes
Key, Hybrid/PBX
Telephones
All (display support on 4400-Series, MLX, ETR, and MLS telephones)
System Programming
System-wide
Specify modules that provide primary, secondary, and tertiary clock synchronization and source of clock synchronization; also activate/deactivate clock:
- LinesTrunks
or More ClockSync
Specify type of facility connected to 100D module:
- LinesTrunks LS/GS/DS1
Type
Specify framing format for 100D module:
- LinesTrunks LS/GS/DS1
FrameFormat
Specify line coding for 100D module:
- LinesTrunks LS/GS/DS1
Suppression
Specify line compensation between 100D module and channel service unit (CSU) or far end:
- LinesTrunks LS/GS/DS1
Line Comp
Specify type of CSU equipment provided by Central Office:
- LinesTrunks LS/GS/DS1
Channel Unit
Specify the type of switch:
- LinesTrunks PRI
SwitchType
Assign telephone numbers to PRI lines:
- LinesTrunks PRI
Telephone Number
Assign B-channels to group:
- LinesTrunks PRI
B-ChannlGrp B-channels
Assign PRI lines to B-channel groups:
- LinesTrunks PRI
B-ChannlGrp Lines
Specify type of network service for each B-channel group:
- LinesTrunks PRI
B-ChannlGrp
NetworkServ
Specify whether telephone number to send to network for outgoing calls should be copied from line telephone number:
- LinesTrunks PRI
B-ChannlGrp CopyNumber
Specify telephone number to send to network for outgoing calls on PRI lines:
- LinesTrunks PRI
NumberToSend
Assign test line telephone number for each 100D module:
- LinesTrunks PRI
Test TelNum
Set timer and counter thresholds for each 100D module:
- LinesTrunks PRI
Protocol Timers
Assign link layer address or Terminal Equipment Identifier (TEI) of equipment connected to each D-channel:
- LinesTrunks PRI
Protocol TEI
To select T1 emulation:
- LinesTrunks LS/GS/DS1
Enter Type
T1 Enter
Select type of emulation
To select T1 Switched 56 Data and program Channel
Signaling:
- LinesTrunks LS/GS/DS1
Enter Type
T1 Enter
or More S56 Data
Enter AssignChan-Signling
Enter Select Direction , Intype
, Outtype , AnsSupv , Disconnect , Inmode , or Outmode
To select T1 All Switched 56 Data and program Channel Signaling:
- LinesTrunks LS/GS/DS1
Enter Type
T1 Enter
or More All S56 Data
Signling Enter
Select Direction , Intype , Outtype , AnsSupv , Disconnect , Inmode
, or Outmode
To select T1 Switched 56 Data and program Incoming Routing Table:
- LinesTrunks LS/GS/DS1
Enter Type
T1 Enter
or More S56 Data
Enter Incom Routing Table
Select Expected Digits, Add Digits, or Delete Digits
Enter
To select T1 All Switched 56 Data and program Incoming Routing Table:
- LinesTrunks LS/GS/DS1
Enter Type
T1 Enter
or More ALL S56 Data
Incom Routing Table Select Expected
Digits, Add Digits, or Delete Digits
Enter
Maximums
General
100D modules
3
PRI-specific
B-channels
Lines (total)
Digits for each number assigned to a PRI line
ISDN lines for each B-channel group
B-channels for each B-channel group
69
72
12
24
23
Digits for each telephone number sent to network for outgoing calls
Digits for test trunk telephone number
PRI Dial Plan Routing Table (Hybrid/PBX)
Number of entries
Digits for each pattern
Digits to delete
Digits to add
12
12
16 (0-15)
8
14 (range 0-14, 0 = wildcard)
4
Network Selection Table
Number of entries
Digits for each pattern
4 (0-3)
8 (* = wild card; at least one * required; all *s must be at end and contiguous.)
Special Services Selection Table
Number of entries
Digits for each pattern
Digits to delete
8 (0-7)
4
4 (range 0-4)
Call-by-Call Services Table
Number of entries
Number of patterns for each entry
Digits for each pattern
Digits to delete
10 (0-9)
10
8
8 (range 0-8)
T1-specific
T1 Dial Plan Routing Table
Number of entries
Expected Digits
Digits to delete
Digits to add
24 (1-24)
3 (range 1-3)
4 (range 0-4)
4 (range 0-4)
Factory Settings
System-wide
Primary Clock
Clock Synchronization Source
Clock
First port that is in service on an 800 NI-BRI module or first 100D module in service in control unit
Loop (not definable by System Manager)
Active
Type of Facility
Framing Format
Line Coding
Signaling
Line Compensation
T1
D4 compatible
AMI-ZCS
Robbed-Bit Signaling (RBS)
1 (range 1-5)
1 = 0.6 dB loss
2 = 1.2 dB loss
3 = 1.8 dB loss
4 = 2.4 dB loss
5 = 3.0 dB loss
PRI
Telephone number assigned to PRI line
B-channels assigned to group
PRI lines assigned to B-channel groups
Type of network service for each B-channel group
0 digits
None
None
None
Copy telephone number to send from telephone number assigned
Telephone number to send to network for outgoing PRI calls
Test trunk telephone number for each 100D module
Do Not Copy
0 digits
None
Call-by-Call Services Table
Patterns
Call type
Service
Digits to delete
Blank
Both (Voice and Data)
Blank
0
Timer/counter thresholds for each 100D module
T200 Timer
T203 Timer
N200 Counter
N201 Counter
K Counter
T303 Timer
T305 Timer
T308 Timer
T309 Timer
T310 Timer
T313 Timer
T316 Timer
1 second (range 1,000-3,000 ms)
30 seconds (range 1-60)
3 transmissions (range 1-5)
260 octets (range 16-260)
7 frames (range 1-15)
4 seconds (range 4-12)
4 seconds (range 4-30)
4 seconds (range 4-12)
90 seconds (range 30-120)
60 seconds (range 2-120)
4 seconds (range 4-60)
120 seconds (range 30-120)
PRI Dial Plan Routing Table
Service value
Digits for each pattern
Digits in Called Party Number
Digits to add
Empty
Blank
0
T1 Dial Plan Routing Table
Expected Digits
Digits to delete
Digits to add
Blank
Blank
0
Blank
Tandem PRI Trunks1
B-channels assigned to group
Type of network service for the B-channel group
Copy telephone number to send from telephone number assigned
All
ETN (Electronic Tandem Network)
Copy
