|
This topic covers the following items:
Intended audience
This topic is intended primarily for the on-site technical personnel
who are responsible for installing the system and performing initial
administration and acceptance testing.�However, the general precautions
are intended for both installers and system administrators.
Safety and security alert labels
This topic uses the following symbols to call your attention to
potential problems that could cause personal injury, damage to equipment,
loss of data, service interruptions, or breaches of toll fraud security.
Caution:� Indicates the presence of a hazard that, if not
avoided, can or will cause minor personal injury or property damage,
including loss of data.
Warning!:� Indicates the presence of a hazard that, if not
avoided, can cause death or severe personal injury.
General precautions
Note: The following applies for Message Networking installations
in Sweden, Finland, and Norway only.
Message Networking system relies on a
ground connection through the main plug with an earth contact.�Because
of unreliable earthing concerns in Sweden, Finland and Norway, Message
Networking must be installed by service personnel in a restricted
access location.�A restricted access location is defined as a location
to which access can be gained only by service personnel or customers
who have been instructed about the reasons for the restricted access
and any safety precautions that must be taken.�In these cases, access
to the Message Networking system is gained by the use of a tool
(such as a lock and key) or other means of security.
Caution: Lithium battery(ies) are included with this system.�Do
not puncture, mutilate, or dispose of battery(ies) in fire.�Danger
of explosion if battery is incorrectly replaced.�Replace only with
the same or equivalent type recommended by manufacturer.�Dispose
of used batteries in accordance with the manufacturer's instructions
and your local regulations.
ATTENTION:� Il y a danger d’explosion s’IL y a
remplacement incorrect de la batterie.� Remplacer uniquement avec
une batterie du m�me type ou d’un type �quivalent recommand�
par le constructeur.� Mettre au rebut les batteries usag�es conform�ment
aux instructions du fabricant.
Site preparation
This section describes physical requirements for the installation
site, which include:
Environmental considerations
Place the Message Networking system in an area where the environmental
conditions shown in the following table are maintained.
|
Operating state
|
Temperature
|
Humidity
|
|
Operating
|
+10 to +35�C
(+50 to +95�F)
|
20 to 80%, noncondensing
|
|
Non-operating (in storage or being shipped)
|
-20 to +60�C
(-4 to+140�F)
|
20 to 80%, noncondensing
|
�
Installation area considerations
Caution: Observe the following when determining where to
place the Message Networking system:
- Use only the power cord assembly provided to connect the Message
Networking to an AC main outlet.�
- Install the Message Networking system within 6 feet (2m) of
a grounded AC main outlet.��
- Do not use extension cords with the Message Networking system.
- Ensure that the AC main outlet to be used to power the Message
Networking system (via the power cord) is a grounded outlet. If
you are unsure of the ground integrity of the outlet, have a trained
and certified electrician check the outlet.
- Consideration must be given to the connection of the Message
Networking system to a branch circuit with respect to overload
or overcurrent protection. Check the Message Networking ratings
to ensure that, together with other equipment connected to the
same branch circuit, an overcurrent or overload condition does
not exist.
- Maintain an air-distribution system that provides adequately
cooled, filtered, and humidity-controlled air.
- Do not install the Message Networking system such that the ventilation
or fan openings will be blocked.
Note: The following applies for Message Networking installations
in Sweden, Finland, and Norway only. Message Networking relies on
a ground connection through the main plug with an earth contact.
Because of unreliable earthing concerns in Sweden, Finland and Norway,
the Message Networking must be installed by Service Personnel in a restricted
access location. A restricted access location is defined as a location
to which access can be gained only by service personnel or customers
who have been instructed about the reasons for the restricted access
and any safety precautions that must be taken.�In these cases, access
to the Message Networking is gained by the use of a tool (such as a lock and
key) or other means of security.
Weight and space considerations
The following table lists the approximate weight, height, width,
and depth of each system.
| Weight |
Height |
Width |
Depth |
29 lb
(13 kg) |
19 in.
(49 cm) |
9 in.
(23 cm) with stabilizing feet |
18 in.
(46 cm) |
Add 3 inches (7.6 cm) to accommodate a rear chassis cable support
bracket. If required, add 4 inches (10.2 cm) to accommodate a 356B
adapter and mounting clip.
The following table lists the approximate weight, height, width,
and depth for the monitor and keyboard.
| Peripheral |
Weight |
Height |
Width |
Depth |
| Monitor |
27 LB
(12.2 kg) |
14 in.
(35 cm) |
14 in.
(36 cm) |
15.4 in.
(39 cm) |
| Keyboard |
5 LB
(2.3 kg) |
2.5 in.
(6.4 cm) |
19 in.
(48 cm) |
8 in.
(20.5 cm) |
A monitor is not necessarily ordered and shipped for each system.
The weight and space considerations listed are for those shipments
that include a Sampo 15-inch monitor.
Power requirements
The following table lists the power requirements for the system.
| Attribute |
Requirement |
| Volts AC (VAC) |
100–220 |
| Hertz (Hz) |
60 |
| Phase |
Single |
Amps
(US) |
5A (maximum) |
AMPS
(International) |
�������— |
| Input cords |
NEMA 5–15P plug; 6 ft (2 m) long |
| Unit input receptacles |
IEC320 inlet |
| Maximum Power Output |
200 W |
| Heat Dissipation |
682 BTU |
In addition to the above power requirements, you must also:
- Locate each unit within 6 feet (2 meters) of its power receptacle.
- Keep the communication cables separate from the power cables.
- Install communication and power cables in accordance with National
Electrical Codes (NEC).
Caution: Use only shielded cables and equipment with the
system to maintain safe levels of electromagnetic compatibility.
Shipment contents
The customer should have received boxes containing the computer,
keyboard, and monitor (if ordered).
Be sure that you have the following items packed in the box or
boxes:
- The chassis. Turn out the stabilizing feet on the bottom of
the computer case.
- One 6-foot to 8-foot (2-meter to 3-meter) power cord (depending
on country in which you are doing the installation)
- The keyboard with onboard mouse and split connector cord
- One 4-pin RJ-11 cable for each voice port purchased
- One LAN cable
- One monitor and power cord, if ordered
- One maintenance modem and required cables
Saving packing materials
Save the shipping carton and all packing materials to use in case
you have to return the system to the manufacturer. If you ordered
multiple systems, saving one carton and one set of packing materials
should be sufficient. Packing materials include:
- Antistatic bags
- Cardboard and foam inlays
Note: The packing materials can also include a plastic
bag designed to protect the system from moisture during shipment.
Discard this bag. It is not reusable.
Also save the shipping cartons for the keyboard and monitor.
Top of page
|
