DEFINITY Made Easy Home Page Table of contents Previous page Next page Index Links Frequently asked questions
Go to Upgrades for si Go to Installation for MCC Go to Installation for SCC

Made Easy Tool for DEFINITY Media Server Configurations
Issue 5, October 2002



Bring the System Online

Deliver or install the License File

Return to Task List


Caution! This procedure must be done immediately after you upgrade the software. If the license file is not installed within 10 days, the switch enters a No-License mode and shuts down all call processing.

New Duplicated G3r installations only

  1. Retrieve the RFA License File with both serial numbers from the RFA Application.

  2. Type set time and press Enter.

    3. Ensure that the system date and time are set correctly.

  3. Use one of these installation methods:

  4. Type save translation and press Enter.

    5. After the translations have been copied (about 10 minutes), the system returns an error code, which must be a zero; otherwise, the translations are not copied.

  5. Type reset system 4 and press Enter.

    6. Wait until the system has completely reset before continuing.

  6. Type change cabinet 1 and press Enter.

    7. In the Carrier Type column change the "B" carrier to processor and submit the form.

  7. Type change system-parameters duplication and press Enter.

    8. Set the Enable Operation of SPE Duplication field to y and submit the form.

  8. Type save translation and press Enter.

    9. After the translations have been copied (about 10 minutes), the system returns an error code, which must be a zero; otherwise, the translations are not copied.

  9. Type reset system 3 preserve-license (or reset system 3 no-preserve-license, since the License File has been saved in translations) and press Enter.

New simplex and upgraded G3r only

  1. Type save translation and press Enter.

    2. After the translations have been copied (about 10 minutes), the system returns an error code, which must be a zero; otherwise, the translations are not copied.

  2. Type reset system 3 and press Enter.

    3. Wait until the system has completely reset before continuing.

  3. If the system has IP endpoints registered, unplug the Ethernet cable from the TN799 (C-LAN) circuit pack.

    4. This disconnects (unregisters) all IP endpoints.

  4. Type set time and press Enter.

    5. Ensure that the system date and time are set correctly.

  5. Use one of these installation methods:

New or upgraded G3si only

  1. Retrieve the RFA License File with both serial numbers from the RFA Application.

  2. If the system has IP endpoints registered, unplug the Ethernet cable from the TN799 (C-LAN) circuit pack.

    3. This disconnects (unregisters) all IP endpoints.

  3. Type set time and press Enter.

    4. Ensure that the system date and time are set correctly.

  4. For duplicated systems only type status system all and press Enter.

    5. Ensure that the standby SPE is not in the maintenance state. If it is, wait for the maintenance state to finish.

  5. Use one of these installation methods:

Direct connection between the switch and RFA
  1. Go to the RFA website, and, following the instructions in the "Deliver to G3r/G3si/G3csi" chapter of the RFA Job Aid, deliver the License File.


Note: This procedure sends the License File to the switch and installs it.

  1. If the system has IP endpoints registered, and you unplugged the Ethernet cable from the TN799 (C-LAN) circuit pack, replug the cable.

    2. This re-registers the IP endpoints.

No connection between the switch and RFA
  1. Go to the RFA website, and, following the instructions in the "Deliver to G3r/G3si/G3csi" chapter of the RFA Job Aid, deliver the License File to your laptop/PC.

  2. Open the License Installation Tool (LIT) application at your laptop/PC.

  3. Use the LIT instructions to add a switch connection profile to the tool.

  4. Use the LIT instructions to install the License File on the switch.

  5. If the system has IP endpoints registered, and you unplugged the Ethernet cable from the TN799 (C-LAN) circuit pack, replug the cable.

    6. This re-registers the IP endpoints.

Return to Task List

DEFINITY Made Easy Home Page Table of contents Previous page Next page Index Links Frequently asked questions
Go to Upgrades for si Go to Installation for MCC Go to Installation for SCC
Copyright� 2002 Avaya Inc.
Send comments to MadeEasy Development Team



Always check at the Made Easy Web site for the most current information.