The View Administrative Option

If you are using static addressing and encounter problems, use the following procedure to verify the current values of system parameters and file versions.

NOTE: Unless otherwise prevented using administration, the user can view but not change most of the parameters associated with Craft Local Procedures. For more information about this option, see the applicable user guide(s).

NOTE: If the View Network Information option is not available due to being disabled by administration, use the ADDR option to view IP Addresses. See Static Addressing Installation in Chapter 3: Local Administrative Options. The IP Addresses might have been entered incorrectly. Verify whether you were provided with correct IP Addresses.

When you select VIEW from the Craft Local Procedure Screen, the following text displays:


Static Addressing screen			Line Description and (System Value)
Phone Call Server Router Mask File Server 802.1Q VLAN ID VLAN Test	nnn.nnn.nnn.nnn nnn.nnn.nnn.nnn nnn.nnn.nnn.nnn nnn.nnn.nnn.nnn nnn.nnn.nnn.nnn NVL2Q text string dddd ddd		Telephone IP Address (IPADD) Call Server in use; media server IP Address Router in use; gateway/router Ip Address IP network mask (NETMASK) IP Address of HTTP/S File Server in use NVL2Q setting text description NVL2QVLAN NVVLANTEST

Use the Right and Left navigation arrows to scroll through the viewable information, shown in Table 2.

Table 2: Parameter Values
Name	System Value	Format
Phone	*nnn.nnn.nnn.nnn*	Telephone IP Address; IPADD value.
Call server	*nnn.nnn.nnn.nnn*	IP Address of the call server currently in use, otherwise “0.0.0.0.”
802.1X	If DOT1X = 0 If DOT1X = 1 If DOT1X = 2	Pass-thru mode. Pass-thru with Logoff. Supplicant mode.
Router	*nnn.nnn.nnn.nnn*	Up to 15 ASCII characters: the IP Address of the router in use.
Mask	*nnn.nnn.nnn.nnn*	Up to 15 ASCII characters: NETMASK value.
File server	*nnn.nnn.nnn.nnn*	IP Address of last file server used successfully during initialization or “0.0.0.0” if no file server was used successfully.
802.1Q	*cccc*	Text string corresponding to the NVL2Q value.
VLAN ID	*cccc*	Up to 4 ASCII characters. Value is L2QVLAN text "Auto" if 802.1Q tagging is 0 or "On" if 802.1Q tagging is 1. If 802.1Q tagging is off (2), this line is not displayed.
VLAN Test	*ccc*	Up to 3 ASCII characters. Value is VLANTEST value if 802.1Q tagging is 0 or 1. If 802.1Q tagging is off (2), this line is not displayed.
Ethernet		Text string corresponding to PHY1STAT value, for example, “auto,” “100Mbps HDX,” 1000Mbps FDX.”
PC Ethernet		Test string corresponding to PHY2STAT value, for example, “disabled,” “100Mbps HDX,” 1000Mbps FDX.”.
Model	*96ccDccc*	Up to 8 ASCII characters: MODEL serial number.
Phone SN	*cccccccccccccccccc*	Telephone Serial Number, up to 18 ASCII characters.
PWB SN	*cccccccccccccccccc*	Printed Wiring Board (circuit board) Serial Number, up to 18 ASCII characters. Applies only to 96xx IP Telephones that have a software-readable PWB serial number and comcode.
PWB comcode	*nnnnnnnnn*	9 ASCII numeric characters. Applies only to 96xx IP Telephones that have a software-readable PWB serial number and comcode.
MAC address	*hh:hh:hh:hh:hh:hh*	Each octet of the MAC address displays as a pair of hexadecimal numbers.
Group	*nnn*	Up to 3 ASCII numeric characters: GROUP value.
Protocol: Application File “big app” Ethernet Boot file “little app”	*cccccccc* *filename.ext* *cccccccc* *Ethernet bootcodename*	Up to 8 ASCII characters, currently only “H.323.” 4 to 32 ASCII characters (primary application). 2 to 8 ASCII characters, either"1000Mbps", “100Mbps”, “10Mbps”, or “No.” 1 to 32 ASCII characters (backup image name).
GigE Adapter	*cccccccccccccc*	14 ASCII characters. Version identifier of the GigE Adapter software, if applicable.
Button Module 1	*cccccccccccccc*	14 ASCII characters. Version identifier of the software in the first attached Button Module, if applicable.
Button Module 2	*cccccccccccccc*	14 ASCII characters. Version identifier of the software in the second attached Button Module, if applicable.
Button Module 3	*cccccccccccccc*	14 ASCII characters. Version identifier of the software in the third attached Button Module, if applicable.

Press Back at any time to return to the Craft Local Procedure screen.