Avaya Support Forums

Avaya Support Forums (http://support.avaya.com/forums/index.php)
-   IP Telephony and Convergence (http://support.avaya.com/forums/forumdisplay.php?f=8)
-   -   Remove plus + added for CM (http://support.avaya.com/forums/showthread.php?t=3721)

chelungas 10-03-2013 11:43 AM

Remove plus + added for CM
 
Hi everybody,

Did someone know how to remove plus + added for CM in sip trunk, without using SBC??

thanks

aa1 10-04-2013 12:44 AM

Remove plus + added for CM --> Prepend '+' to Calling Number? n
 
There is a field on the trunk group form (page 4) that might help you!

display trunk-group xxx Page 4 of 21
PROTOCOL VARIATIONS
Mark Users as Phone? n
Prepend '+' to Calling Number? n <===========



Please take a look at the below for more information

Avaya Aura® Communication Manager Screen Reference
Release 6.3 03-602878 Issue 5 October 2013
Page 815
https://downloads.avaya.com/css/P8/documents/100171650

Prepend '+' to Outgoing Calling/Alerting/Diverting/Connected Public Numbers
If you set the Prepend '+' to Outgoing Calling/Alerting/Diverting/Connected Public Numbers field on the SIP Signaling Group screen to y and if Communication Manager uses the public-unknown-numbering table, Communication Manager inserts a leading plus (+) digit in calling, alerting, diverting, or connected numbers. The default value is n.
If the Peer Server field on the SIP Signaling Group screen is SM, the system sets the Prepend '+' to Outgoing Calling/Alerting/Diverting/Connected Public Numbers field to display-only, with the default value of y. If the Peer Server field on the SIP Signaling Group screen is Others, the system sets the Prepend '+' to Outgoing Calling/Alerting/Diverting/Connected Public Numbers field to n and as editable.

Arbi

msantos 01-24-2014 02:52 PM

How to remove plus + added for CM in sip trunk
 
# Verify 3 things:
  1. Trunk Group SIP:
    • “Prepend '+' to Calling/Alerting/Diverting/Connected Number? N”.
  2. SIP Signaling Group screen to N:
    • “Prepend '+' to Calling/Alerting/Diverting/Connected Number? N
  3. Trunk Group SIP, if use “Numbering Format: public”, change from "public" to "private".
    • Page- display public-unknown-numbering ....Note: If an entry applies to a SIP connection to Avaya Aura(R) Session Manager, the resulting number must be a complete E.164 number.
      Communication Manager
      automatically inserts a '+' digit in this case.
More information:
Manual - Settings: "Administering Public Unknown Numbering" page 22. LINK: https://downloads.avaya.com/css/P8/documents/100091073
;)
Michel

fcippa 04-12-2016 08:01 AM

remove +
 
I am using private numbering and found that if you use lev0-pvt in the numbering format it will remove the +.

dunmo1 08-25-2021 07:09 AM

Hi All,

5 years later and now I need to do this. Can someone advise how it was done? Basically I have configured one-x communicator to connect to the GAL on outlook but all the numbers are in the e.164 format with the + so users cannot just click the number and dial they have to remove the + manually. From the above it seems possible but not sure how.

cgarciamerc1 01-05-2022 03:26 PM

Remove Plus sign by creating a new signal group (and TG)
 
This can be done with a signal group that has Peer detection disabled, Peer server set to Others.

This will let you set the "Prepend '+' to Outgoing..." value to N.


Peer Detection Enabled? n Peer Server: Others Clustered? n
Prepend '+' to Outgoing Calling/Alerting/Diverting/Connected Public Numbers? n


All times are GMT -7. The time now is 11:34 AM.