Call Detail Recording Option Settings

DEFINITY Made Easy Tools
Issue 3, December 2001

Option Switch Settings

Call Detail Recording Option Settings

Return to Task List

The interface between the system and Call Detail Recording (CDR) equipment may be one of the following:

Data Module -- Recommended option settings are shown in Options for D-Lead and Attention Control Modems.

Modem -- Recommended option settings are in modem vendor document

TN726 Data Line circuit pack and an Asynchronous Data Unit -- Data modules or modems are not required.

Connected directly to the DCE connector (Electronic Industries Association [EIA] Port) located on the rear of the Control Carrier -- Data modules or modems are not required.

A 572 Printer can be used as an output receiving device for Call Detail Recording (CDR). The recommended option settings for this printer are shown in 572 Printer Used with Management Terminal, CDR, and Journal Printer and 572 Printer Used as System Printer. Also, a TELESEER, Call Detail Recording (CDR), 94A Local Storage Unit (LSU), or Customer Premises Equipment (CPE) can be used as the output receiving device.

Administration procedures for Call Detail Recording (CDR) equipment are provided in DEFINITY Enterprise Communications Server Administrator's Guide.


Options for D-Lead and Attention Control Modems
Set Option Display	Option	D-Lead Settings	Attention Control Settings
Set 300 Speed?	300	Note 1	Note 1
Set 1200 Speed?	1200	Note 1	Note 1
Set 2400 Speed?	2400	Note 1	Note 1
Set 4800 Speed?	4800	Note 1	Note 1
Set 9600 Speed?	9600	Note 1	Note 1
Set 19200 Speed?	19200	Note 1	Note 1
Set AT Control?	AT	OFF	ON
Set CI Lead?	CI	Note 2	Note 2
Set CI2 Lead?	CI2	Note 2	Note 2
Set CH Lead?	CH	Note 2	Note 2
Set CH2 Lead?	CH2	Note 2	Note 2
Set LL Lead?	LL	Note 2	Note 2
Set REMOTE Loop?	REMLOOP	Grant	Grant
Set RL Lead?	RL	Note 2	Note 2
Set SIGLS Disc?	SIGLS DISC	ON	ON
Set TM Lead?	TM	Note 2	Note 2

Table 3.
572 Printer Used with Management Terminal, CDR, and Journal Printer
Function	Function Name	Menu	Menu Status
01	FORM LENGTH	09	11
02	LPI	01	6
03	CPI	01	10
04	LQ or NLQ	01	LQ
05	BUZZER	01	ON
06	FONT	02	FONTCART
07	RESOLUTION	01	144
11	BUFFER	02	N-LINE
13	PW ON MODE	01	ON-LINE
14	DIRECTION	01	B1-DIR.1
15	BUFF FULL	02	LF + CR
16	P.E.	01	ACTIVE
17	AUTO CARRIAGE RETURN (CR)	01	CR + LF
18	ZERO	01	0
22	AUTO LINE FEED	01	CR ONLY
31	1'' SKIP	01	OFF
32	CHAR.SET (GO, GL)	02	USA
33	CHAR.SET (G1, GR)	01	UK
34	CHAR SET (G2)	03	GE
35	CHAR SET (G3)	07	LINE DRAWING
81	OFF-LINE STATE	01	ALL RECEIVE
82	DSR	02	OFF
83	REQUEST TO SEND (RTS) TIMING	01	RTS
84	CD	02	OFF
85	CLEAR TO SEND (CTS)	02	OFF
91	OVER RUN	02	256
92	DATA BIT	02	8
93	PROTOCOL	03	XON/XOFF
94	STOP BIT	01	1
95	PARITY	01	NONE
96	PBS (matches connected device)	01	9600

Table 4.
572 Printer Used as System Printer
Function	Function Name	Menu	Menu Status
01	FORM LENGTH	09	11
02	LPI	01	6
03	CPI	01	10
04	LQ or NLQ	01	LQ
05	BUZZER	01	ON
06	FONT	02	FONTCART
07	RESOLUTION	01	144
11	BUFFER	02	N-LINE
13	PW ON MODE	01	ON-LINE
14	DIRECTION	01	B1-DIR.1
15	BUFF FULL	02	LF + CR
16	P.E.	01	ACTIVE
17	AUTO CARRIAGE RETURN (CR)	01	CR + LF
18	ZERO	01	0
22	AUTO LINE FEED	01	CR ONLY
31	1'' SKIP	01	OFF
32	CHAR.SET (GO, GL)	02	USA
33	CHAR.SET (G1, GR)	01	UK
34	CHAR SET (G2)	03	GE
35	CHAR SET (G3)	07	LINE DRAWING
81	OFF-LINE STATE	01	ALL RECEIVE
82	DSR	02	OFF
83	REQUEST TO SEND (RTS) TIMING	01	RTS
84	CD	02	OFF
85	CLEAR TO SEND (CTS)	02	OFF
91	OVER RUN	02	256
92	DATA BIT	02	8
93	PROTOCOL	03	XON/XOFF
94	STOP BIT	01	1
95	PARITY	01	NONE
96	PBS	04	1200