TOC Index Search

 

Determining an Available SCSI ID

To determine an available SCSI ID for the external disk cartridge drive:

  1. Verify what type of external disk cartridge drive is in the RUK.

    2. The RUK contains either an external JAZ disk cartridge drive or Magneto-Optical (MO) disk cartridge drive. See External JAZ Disk Cartridge Drive Settings and External Magneto-Optical (MO) Disk Cartridge Drive Settings.

  2. Use the information in the following table to determine the recommended SCSI ID for either the JAZ or MO external disk cartridge drive:
     
    IF the system is a...
    AND has this many drives...
    THEN use SCSI ID...
    Notes
    • MAP/40
    One to two
    • 5 (JAZ)
    • 4 (MO)
    After shutting down the system, go to Installing the SCSI Interface Circuit Card in the MAP/40 System.
    • MAP/40P
    • MAP/100
    • MAP/100P
    One to five
    • 5 (JAZ)
    • 4 (MO)
    After shutting down the system, skip Disconnecting the Tape Drive Power Cable and go to Attaching the External Disk Cartridge Drive.
    • MAP/100
    Six
    3 (JAZ or MO)
    After shutting down the system, go to Disconnecting the Tape Drive Power Cable.
    • MAP/100P
    Six
    6 (JAZ or MO)
  3. Determine whether the recommended SCSI ID is available. From the Avaya Intuity Main Menu, select:

    4. Customer/Services Administration

    	System Verification

    		View Installed Hardware

    The system displays the View Installed Hardware Window.

  4. Press F3 (Nextpage) to view all assigned SCSI IDs. Confirm whether the recommended SCSI ID can be used. If not, select another available SCSI ID.

    5. Possible SCSI IDs range from 0 through 6.

Shutting Down the System

To shut down the system:

  1. Start at the Avaya Intuity Main Menu and select:

    2. Customer/Services Administration
    	System Management
    		System Control
    			Shutdown System

  2. Do one of the following:
  3. Watch for messages that indicate that a shutdown is in progress.

    4. When the system is completely shut down, the system displays the following message:

    The system is down.
    Press CTRL-ALT-DEL to reboot your computer.

  4. Turn the power switch off.

Installing the SCSI Interface Circuit Card in the MAP/40 System


 

Note: This task is used only with old MAP/40 systems that do not have an external SCSI connection. If the MAP/40 system has an external SCSI connection or if the old system is not a MAP/40, skip this task and go to the next task.

To install the SCSI interface card from the RUK in the MAP/40 system:

  1. Look in the back of the system at the second slot from the top and then do one of the following:
  2. Remove the dress cover from the front of the system.
  3. Remove the four screws from the bottom of the system that retain the dress cover, and then remove the dress cover.
  4. Loosen the screws retaining the circuit card cage cover, and then remove the cover.


    5. Observe proper electrostatic discharge precautions when you handle computer components. Wear an antistatic wrist strap that touches your bare skin and connect the strap cable to an earth ground. For detailed electrostatic discharge instructions, see Protecting Against ESD Damage on the Intuity Messaging Solutions Release 5 Documentation for Technicians CD-ROM, 585-313-807.

  5. Locate the SCSI interface circuit card and then remove the system cables from the SCSI interface card.
  6. Remove the circuit card retaining screw.
  7. Gently remove the SCSI interface circuit card from the MAP/40 system.
  8. Remove the SCSI interface circuit card from the RUK and then take it out of the antistatic bag.
  9. Insert the SCSI interface circuit card in the open slot.
  10. Connect the system cables.

Disconnecting the Tape Drive Power Cable


 

Note: This task is used only if the old MAP/100 or MAP/100P system has six hard disk drives. If the old MAP/100 or MAP/100P system has fewer than six hard disk drives, go to the next task, Attaching the External Disk Cartridge Drive.

This task releases a SCSI ID for use by the external cartridge drive when all IDs have been taken.

MAP/100 Steps

To disconnect the power cable from the tape drive on the MAP/100 system:

  1. Open the right front dress cover and locate the four screws that secure the peripheral bay to the MAP/100 case.
  2. Loosen the screws one-quarter turn.
  3. Slide the peripheral bay out to the safety stop.
  4. Remove the right side dress cover and locate the seven screws that secure the peripheral bay access cover.
  5. Loosen the seven screws one-quarter turn.
  6. Open the access cover.
  7. Locate the back of the tape drive at the top of the peripheral bay.
     


    Do not remove the flat ribbon SCSI cable from the back of the tape drive. The cable must remain attached for SCSI IDs to be allocated properly.

  8. Remove the power cable from the back of the tape drive.


    9.  

    Tip: The power cable has four colored wires.

  9. Go to the next task.
MAP/100P Steps

To disconnect the power cable from the tape drive on the MAP/100P system:

  1. Open the front dress cover on the MAP/100P
  2. Remove the four screws that secure the peripheral bay to the MAP/100P case.
  3. Lift the peripheral bay out of the MAP/100P case.
     


    Do not remove the flat ribbon SCSI cable from the back of the tape drive. The cable must remain attached for SCSI IDs to be allocated properly.

  4. Remove the power cable from the back of the tape drive.


    5.  

    Tip: The power cable has four colored wires.


     

    Note: Do not tuck the power cable back into the cabinet. Leave the power cable where it can be reached in case the cable must be reattached.

  5. Go to the next task.

Attaching the External Disk Cartridge Drive

To attach the external disk cartridge drive to the old system:

  1. Remove the external disk cartridge drive from the RUK.
  2. Determine what type of external disk cartridge drive the RUK contains, for example, either an External JAZ Disk Cartridge Drive or an External Magneto-Optical (MO) Disk Cartridge Drive.
  3. Do one of the following:
  4. Confirm that the Intuity AUDIX system is completely powered down.
  5. Find the SCSI port on your platform.

    6. The SCSI port is most likely found at or near the standard location shown in External SCSI Connectors, except MAP/100P or MAP/100P External SCSI Connector.

  6. Remove the external SCSI terminator, if one exists, from the system SCSI connection.
  7. Determine which of three cables from the RUK to use to connect the external SCSI connector to the external cartridge drive. Depending on the external disk cartridge drive, the SCSI port is one of three types shown in either Cables for External JAZ Disk Cartridge Drive or Cables for External MO Disk Cartridge Drive.
  8. Connect one end of the cable to the upper SCSI connector on the back of the external cartridge drive. See either External JAZ Disk Cartridge Drive Settings or External Magneto-Optical (MO) Disk Cartridge Drive Settings.
  9. Attach the other end of the cable to the external SCSI connector on the old system.
  10. Connect the external drive to electrical power and turn on the power switch. This switch is located at the back right side of the drive.
     

    Note: The external drive must be turned on before you can turn on the power for the Avaya Intuity system.

Avaya Communication
http://www.avaya.com
Avaya UCS Information Development
TOC Index Search