|
|
|
This chapter’s Introduction indicates that there are many parameters you can administer for the 4600 Series IP Telephones. This section explains how to change parameters by means of the DHCP or TFTP/HTTP servers. In all cases, you are setting a system parameter in the telephone to a desired value. Table 7 lists the parameter names, their default values, the valid ranges for those values, and a description of each one. For DHCP, the DHCP Option sets these parameters to the desired values as discussed in DHCP Generic Setup. For TFTP and HTTP, the parameters in Table 7 are set to desired values in the Script File, as discussed in Contents of the Upgrade Script.
We recommend that you administer options on the 4600 Series IP Telephones using script files. Some DHCP applications have limits on the amount of user-specified information. The administration required can exceed those limits, for example, for a 4630 with all applications administered.
You might choose to completely disable the capability to enter or change option settings from the dialpad, as of Release 1.8. As of that Release, a new system value, PROCPSWD, can be set as part of standard DHCP/TFTP administration. If PROCPSWD is non-null and consists of 1 to 7 digits, the user cannot invoke any “dialpad options” without first pressing Mute or Hold and entering the PROCPSWD value. See “Chapter 3" of the 4600 Series IP Telephone Installation Guide for more information.
CAUTION: PROCPSWD is likely stored on the server “in the clear” and is certainly sent to the telephone in the clear. Therefore, do not consider PROCPSWD as a high-security technique to inhibit a sophisticated end-user from obtaining access to local procedures.
Administering this password can limit access to all local procedures, including
V I E W, which is read-only and would not change any settings in any case.
| Parameter Name |
Default Value |
Description and Value Range |
|---|---|---|
| AGCHAND |
1 |
Automatic Gain Control status for handset (0=disabled, 1=enabled). |
| AGCHEAD |
1 |
Automatic Gain Control status for headset (0=disabled, 1=enabled). |
| AGCSPKR |
1 |
Automatic Gain Control status for Speaker (0=disabled, 1=enabled). |
| AUDIOENV |
|
Audio environment selection index (0 to 80). For more information, see Audio Customization. |
| AUDIOSTHD |
0 |
Headset sidetone setting (0=No change, 1=6dB below nominal, 2=no sidetone - infinite loss). |
| AUDIOSTHS |
0 |
Handset sidetone setting (0=No change, 1=6dB below nominal, 2=no sidetone - infinite loss). |
| AUTH |
0 |
Script file authentication value (0=HTTP is acceptable, 1=HTTPS is required). |
| CALLFWDSTAT |
0 |
Controls which Call Forwarding Feature Buttons are active and visible to the user. Valid value is one ASCII numeric digit, 0 to 7. Values are: 0 = No call forwarding 1 = Call Forward 2 = Call Forward Busy 3 = Call Forward and Call Forward Busy 4 = Call Forward No Answer 5 = Call Forward and Call Forward No Answer 6 = Call Forward Busy and Call Forward No Answer 7 = Call Forward, Call Forward Busy and Call Forward No Answer |
| CNAPORT |
8888 |
Avaya Converged Network Analyzer (CNA) server registration transport-layer port number (0-65535). Applies only to H.323 telephones. |
| CNASRVR |
“AvayaCNAserver” |
Text string containing the IP Addresses of one or more Avaya Converged Network Analyzer (CNA) servers, in dotted decimal or DNS format. Applies only to H.323 telephones. |
| COVERAGEADDR |
“” (Null) |
Call Coverage/Messages URI for SIP telephones. The URI used for Call Coverage and Messages buttons. Valid values are zero or one URI (0 to 255 ASCII characters). Null (“”) is a valid value, but the value may not contain spaces. |
| CTISTAT |
1 |
Computer-Telephony Integration (CTI) Status (1=enabled, 0=disabled). Applies only to H.323 telephones. |
| CTIUDPPORT |
49721 |
CTI UDP listener port (49714 through 49721, inclusive). Applies only to H.323 telephones. |
| DATESEPARATOR |
/ |
Date Separation Character for SIP telephones. Valid value is one ASCII graphic character from exclamation point (hex 21) through tilde (hex 7E). Null (“”) is not a valid value. The specified character is used to separate the month, day, and year on the telephone display. |
| DATETIMEFORMAT |
0 |
Time/Date Display Format for SIP telephones. Valid value is one ASCII numeric digit, 0 to 3. The values and associated Time and Date format the SIP telephones display are: 0 = 12-hour time, mm/dd/yy 1 = 12-hour time, dd/mm/yy 2 = 24-hour time, mm/dd/yy 3 = 24-hour time, dd/mm/yy See Setting the Date and Time on SIP IP Telephones for more information. |
| DHCPSTD |
0 |
DHCP Standard flag. If set to “1” the telephone strictly follows the DHCP standard with respect to giving up IP Addresses when the DHCP lease expires. If set to “0” the telephone continues using the IP Address until it detects reset or a conflict (see DHCP Generic Setup). |
| DIALPLAN |
“” (Null) |
The Dial Plan for SIP telephones. Valid values are zero to 1000 of the following ASCII characters: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, *, #, x, Z, z, [, ], -, +, |. See Setting the Dial Plan on SIP IP Telephones for specific guidelines. |
| DIALWAIT |
5 |
Dialing Timeout Interval for SIP telephones. Valid values are one or two ASCII numeric digits, 0 to 10. This parameter controls how many seconds the telephone waits after each dialable character is dialed. If an appropriate dial plan has not been defined, the SIP phone assumes the number is complete and initiates a call when the timeout interval is reached. |
| DNSSRVR |
" " (Null) |
Text string containing the IP Address of one or more DNS servers, at least one of which must be a valid, non-zero, dotted decimal address. |
| DOMAIN |
" " (Null) |
Text string containing the domain name to be used when DNS names in system values are resolved into IP Addresses. |
| DSTOFFSET |
1 |
Daylight Savings Time Offset from Standard Time for SIP telephones. Valid value is one ASCII numeric digit, 0 to 2. The number of hours that clocks change between Standard Time and Daylight Savings Time. |
| DSTSTART |
1SunApr2L |
Daylight Savings Time Start Date for SIP telephones. Valid values are six, seven or nine ASCII characters with a format of either odddmmmht or Dmmmht, where: o is 1 character representing an ordinal adjective as follows: 1 (first), 2 (second), 3 (third), 4 (fourth) or L (last); ddd is 3 characters containing the English abbreviation for the day of the week as follows: Sun, Mon, Tue, Wed, Thu, Fri or Sat; mmm is 3 characters containing the English abbreviation for the month as follows: Jan, Feb, Mar, Apr, May, Jun, Jul, Aug, Sep, Oct, Nov or Dec; h is 1 numeric digit representing the time at which to make the adjustment, exactly on the hour at hAM (0h00 in military format), where valid values of h are 0 through 9; t is 1 character representing the time zone relative to which to make the adjustment as follows: L (local time) or U (Universal Time); and, D is 1 or 2 ASCII digits representing the date of the month, from 1 or 01 to 31, or the character L, which means the last day of the month. For example, a value of “1SunApr2L” means “the first Sunday in April at 2AM local time,” and a value of “29Mar1U” means “March 29th at 1AM Universal Time.” |
| DSTSTOP |
LSunOct2L |
Daylight Savings Time Stop Date for SIP telephones. Valid values and format are the same as DSTSTART. |
| ENHDIALSTAT |
1 |
Enhanced Dialing Status. If set to “1” the Enhanced Local Dialing feature is turned on for all associated applications. If set to “0” the feature is turned off. |
| GMTOFFSET |
0:00 |
Standard Time Offset from Greenwich Mean Time for SIP telephones. Valid values are a positive or negative number of hours and minutes less than 13 hours (1 to 6 ASCII characters, optionally beginning with “+” or “-”, followed by one or two ASCII numeric digits whose combined value is from 0 to 12, optionally followed by a “:” and two ASCII numeric digits whose combined value is from 00 to 59). |
| IRSTAT |
1 |
Text string containing status of Infrared interface (0=off/disabled, 1=on/enabled). |
| L2Q |
0 |
802.1Q framing value (0=auto, 1=on, 2=off). |
| L2QAUD |
6 |
Layer 2 audio priority value (0 to 7). |
| L2QSIG |
6 |
Layer 2 audio priority value (0 to 7). |
| L2QVLAN |
" " (Null) |
802.1Q VLAN Identifier (1 to 4094). |
| MCPORT |
1719 |
Media server transport-layer port number (0-65535). Applies only to H.323 telephones. |
| MUSICSRVR |
“ ” (Null) |
Music Server IP Addresses for SIP telephones. Valid values are zero or more IP Addresses in dotted-decimal or DNS name format, separated by commas without any intervening spaces (0 to 255 ASCII characters, including commas). Null (“”) is a valid value, but the value may not contain spaces. |
| MWISRVR |
“ ” (Null) |
Message Waiting Server IP Addresses for SIP telephones. Valid values are zero or more IP Addresses in dotted-decimal or DNS name format, separated by commas without any intervening spaces (0 to 255 ASCII characters, including commas). Null (“”) is a valid value, but the value may not contain spaces. |
| NTWKAUDIO |
0 |
Network Audio Quality Assessment Display (1=on, 0=off). |
| OPSTAT |
111 |
Options status flags. Consists of 3 “bits” of the form abc, where each letter represents a 0 (disabled/off) or 1 (enabled/on). The first bit, a, controls the setting for all options not controlled by the second or third bits. The second bit, b, controls the setting for view-oriented options (for example, the 4620’s View IP Settings option), if applicable. The third bit, c, controls the setting for the LOGOFF option, if applicable. |
| PHNCC |
1 |
Telephone country code. The administered international country code for the location of the serving MultiVantage server. Range: 1-3 digits, from “1” to “999.” |
| PHNDPLENGTH |
5 |
Telephone dial plan length. The length of the administered dial plan for the serving MultiVantage server. Range: 1 or 2 digits, from “3” to “10.” |
| PHNIC |
011 |
Telephone international access code. The digits dialed to access public network international trunks from the serving Multi-Vantage server. Range: 1-4 digits. |
| PHNLD |
1 |
Telephone long distance access code. The digit dialed to access public network long distance trunks from the serving MultiVantage server. Range: 1 digit or " " (Null). |
| PHNLDLENGTH |
10 |
Length of national telephone number. The number of digits in the longest possible national telephone number for the serving Avaya Media Server’s location. Range: 1 or 2 digits, from “5” to “15.” |
| PHNNUMOFSA |
3 |
Number of Session Appearances for SIP telephones. Valid values are a single ASCII numeric digit, 1 to 5. The number of session appearances that will be supported on phones with larger displays. The 4602 and 4602SW always have 2 session appearances. |
| PHNOL |
9 |
Outside line access code. The character(s) dialed to access public network local trunks from the serving Avaya Media Server. Range: 0-2 dialable characters, including " " (Null). |
| PHY1STAT |
1 |
Ethernet line interface setting (1=auto, 2=10Mbps half-duplex, 3=10Mbps full-duplex, 4=100Mbps half-duplex, 5=100Mbps full-duplex). |
| PHY2PRIO |
0 |
Layer 2 priority value for frames received on or forwarded to the secondary Ethernet interface. Set this parameter only when VLAN separation is enabled. Values are from 0-7 and correspond to the drop-down menu selection. |
| PHY2VLAN |
0 |
VLAN identifier used by frames received on or forwarded to the secondary Ethernet interface. Set this parameter only when VLAN separation is enabled. Value is 1-4 ASCII numeric digits from “0” to “4094.” Null is not a valid value, nor can the value contain spaces. |
| PHY2STAT |
1 |
Secondary Ethernet interface setting (0=Secondary Ethernet interface off/disabled, 1=auto, 2=10Mbps half-duplex, 3=10Mbps full-duplex, 4=100Mbps half-duplex, 5=100Mbps full-duplex). |
| PROCPSWD |
" " (Null) |
Text string containing the local (dialpad) procedure password (Null or 1-7 ASCII digits). |
| PROCSTAT |
0 |
Local (dialpad) Administrative Options status (0=all Administrative Options are allowed, 1=only VIEW is allowed). |
| REGISTERWAIT |
3600 |
SIP Re-registration Interval. The SIP registration expiration interval (in seconds) sent to the SIP registrar during registration. Valid values are 1 to 5 ASCII numeric characters from 0 to 65535. Null (“”) is not a valid value, and the value may not contain spaces. |
| RTCPMON |
" " (Null) |
Text string containing the 4-octet IP Address of the RTCP monitor currently in use. |
| RTCPMONPORT |
5005 |
The port used to send RTCP information to the IP address specified in the RTCPMON parameter. |
| SIPDOMAIN |
“ ” (Null) |
SIP Domain Name. Valid values are 0 to 255 ASCII characters. Null (“”) is a valid value, but the value may not contain spaces. The domain name used in the Contact header for SIP registration. For example, if the SIP domain is “avaya.com”, the Contact header sent to the SIP registrar for extension 1234 would be sip:[email protected]. |
| SIPPROXYSRVR |
“ ” (Null) |
SIP Proxy Server IP Addresses. Valid values are zero or more IP Addresses in dotted-decimal or DNS name format, separated by commas without any intervening spaces (0 to 255 ASCII characters, including commas). Null (“”) is a valid value, but the value may not contain spaces. |
| SIPPORT |
5060 |
SIP Server Port Number. Valid values are 1 to 5 ASCII numeric characters from “0” to “65535”. Null (“”) is not a valid value, and the value may not contain spaces. |
| SIPREGISTRAR |
“ ” (Null) |
SIP Registrar IP Addresses. Valid values are zero or more IP Addresses in dotted-decimal or DNS name format, separated by commas without any intervening spaces (0 to 255 ASCII characters, including commas). Null (“”) is a valid value, but the value may not contain spaces. |
| SNMPADD |
" " (Null) |
Text string containing one or more allowable source IP Addresses for SNMP queries, in dotted decimal or DNS format, separated by commas, with up to 127 total ASCII characters |
| SNMPSTRING |
public |
Text string containing the SNMP community string (up to 32 ASCII characters). |
| SNTPSRVR |
“ ” (Null) |
Simple Network Time Protocol (SNTP) Server IP Addresses for SIP telephones. Valid values are zero or more IP Addresses in dotted-decimal or DNS name format, separated by commas without any intervening spaces (0 to 255 ASCII characters, including commas). Null (“”) is a valid value, but the value may not contain spaces. |
| SPEAKERSTAT |
2 |
Hands-Free Audio Operation for SIP IP telephones. Valid value is one ASCII numeric digit, 0 to 2, as follows: 0=No hands-free audio 1=One-way Speaker (monitor) 2=Two-way Speaker |
| STATIC |
0 |
Static programming override flag. If set to “0” static programming never overrides file server- (DHCP or TFTP) or call server-administered data. If set to “1” static programming overrides only file server-administered data. If set to “2” static programming overrides only call server-administered data. If set to “3” static programming overrides both file server- and call server -administered data. |
| TLSSRVR |
" " (Null) |
Text string containing the IP Addresses of one of more Avaya HTTPS servers, in dotted decimal or DNS format. |
| UNNAMEDSTAT |
1 |
Unnamed Registration Status. Specifies whether unnamed registration is initiated if the user fails to enter a value at the Extension: prompt. Unnamed registration provides the telephone with a TTI-level service, enabling a user, for example, to dial emergency services like 911. Value 1=Yes, 0=No. |
| VLANSEP |
1 |
VLAN separation. Controls whether frames to/from the secondary Ethernet interface receive IEEE 802.1Q tagging treatment. The tagging treatment enables frames to be forwarded based on their tags in a manner separate from telephone frames. If tags are not changed, no tag-based forwarding is employed. Values are: 1=Change tags as necessary, 2= Do not change tags. |
| VLANTEST |
60 |
Number of seconds to wait for a DHCPOFFER when using a non-zero VLAN ID (1-3 ASCII digits, from “0” to “999”). |
NOTE: Table 7 applies to all 4600 Series IP Telephones. The 4630/4630SW and
4620/4620SW/4621SW/4622SW/4625SW IP Telephones have additional, optional administration. See Customizing the 4630/4630SW IP Telephone and Customizing 4610SW, 4620/4620SW, 4621SW, 4622SW, and 4625SW IP Telephones for more information.
|
|
|