|
Use the Add New Machine: Octel 100 page to add
a new Octel 100 remote machine to the Message Networking system
or to modify an existing machine.
This page contains the following fields.
New Machine Name: Type the name
of the Octel 100 system that you are adding. The machine name can
be up to 23 alphanumeric characters:
- Enter uppercase letters as uppercase.
- Enter lowercase letters as lowercase.
- Use a hyphen (-) or an underscore (_).
- These names cannot start with a number.
- There can be no blank spaces.
Note: The name must be unique on both the local Message
Networking network as well as any other Message Networking systems
in the network. To ensure that you are using a unique name, check
the Remote Machines List on all Message Networking systems in
your network.
Machine Type: Select Octel
100.
Bridged Machine: Specify whether this remote machine is to be used as a bridged machine. Bridged machines are used by Message Networking to pass messages between nonbridged remote machines. Select yes to indicate that this remote machine is to be used as a bridged machine. If this remote machine is not being used as a bridged machine, select no. The number of remote machines that can be used as a bridge is specified by the Number of Bridged Nodes field on the Customer Options page.
Note: The Bridged Machine field does not appear if the Number of Bridged Machines on the Customer Options page is set to 500 (the maximum).
Send FAX Messages?: Specify whether fax messages
are allowed for the remote machine. Select Yes to allow fax messages
or No to restrict fax messages.
Dial String: Type the main telephone
number of the Octel 100 remote machine, up to 30 characters. The
Message Networking system uses the dial string to contact and send
messages to the remote machine. The dial string typically consists
of the dial-access code needed to reach the network, followed by
a pause interval, followed by the telephone number of the remote
machine.
You can enter the following characters in the dial string field:
0 - 9, P, #, *, and ". To
make the Message Networking system pause for a specific length of
time, type "P" (including the quotes) in the dial
string. Include a single "P" to cause the system to pause
approximately 1.5 seconds. Include a "P" followed by a
digit from 1 to 9 to cause the system to wait the specified number
of seconds.
Mailbox ID Length: Type the number of digits in mailbox IDs on the remote machine, up to 10 digits.
Note: To change the Mailbox ID Length after initial system administration, see Changing a remote machine's mailbox number length for the steps you must complete to successfully change this field.
Default Language: Use this field to specify
the default language on the remote machine. If more than one language is installed
on the system, select the language from the drop-down menu. The default for
this field is en-US (US English).
If you change the Default Language after initial remote machine administration,
subscribers that you subsequently add to the remote machine are assigned the
new Default Language as their default Language ID. However, the Language IDs
of existing subscribers on the remote machine do not change.
Failed Msg. Notification Priority?: Indicates
whether to mark failed message notifications with priority status. Select yes
to mark failed message notifications with priority status. Select no
if you do not want to mark failed message notifications with priority status.
The default for this field is no.
Msg ID?: Specify whether to include the original
message ID in failed message notifications. Select yes to include the
original message ID. Select no if you do not want to include the original
message ID in failed message notifications. The default for this field is no.
Send Message for EAW?: Specify whether the original
message is sent back to a subscriber after that subscriber has sent a message
from this machine to an Aria machine that has the Extended Absence Greeting
(EAG) warning activated. This message return is in addition to the message indicating
the actual EAG warning condition. Select yes to return the original message.
Select no if you do not want to return the original message. The default
for this field is no.
Default NameNet Type: Specify the default NameNet
type, set up on the remote machine, that is used for aging purposes by the remote
machine. Type p if directory entries are permanent. Type u if
entries are usage-based, which indicates that directory entries are temporarily
available based on the network traffic of a particular remote machine. The default
for this field is u.
Organization: Use this field to provide a description
of the organization using Message Networking, up to 64 characters. This field
is optional and for informational purposes only.
Organization Unit: Use this field to provide a description
of the organization unit using Message Networking, up to 64 characters. This field
is optional and for informational purposes only.
Node ID: Unique node ID for this remote
machine. This field is display-only and cannot be modified.
Comments: You can optionally type any comments about
this remote machine, up to 68 alphanumeric characters. This field is optional
and for informational purposes only.
Default Community ID: Community identifier for
all subscribers added to this remote machine. An integer of 1 through 15.
Subscriber Updates Type: Select the type of remote subscriber updates to be sent to this remote machine:
- directory-view: Select directory-view to specify that updates should be sent to the remote machine only for the network address ranges defined in the remote machine's Directory View.
- dynamic: Select dynamic to specify that the remote machine should receive updates for subscribers that exchange messages with this remote machine.
- full: Select full if you want full updates sent for all remote machines on the Message Networking system to this remote machine. If you select full, verify that the remote machine has enough space for information on all subscribers from all remote machines connected to the Message Networking system.
The default for this field is dynamic. To receive no updates, select directory-view, make sure no views are defined for this remote machine, and then set the Updates: Out? field to n.
Updates In: Specify whether the Message Networking
system can receive updated user database information from this remote machine.
Select yes if this Message Networking system accepts updated user information
from this remote machine. Select no if this Message Networking system
does not accept updated user information from this remote machine. The default
for this field is no.
Updates Out?: Specify whether Message Networking
is able to send user information updates to this remote machine. Select yes
if this Message Networking system sends user information updates to remote machines.
Select no if this Message Networking system does not send user information
updates to remote machines. The default for this field is no.
Voiced Names for Dynamic?: If the Subscriber
Updates Type is set to dynamic, specify whether to include the subscriber's
voiced name in the update. You cannot modify this field until a new remote machine
is saved .Select yes to include the voiced name. Select no if
you do not want to include the voiced name. The default for this field is
yes.
ASCII Name Confirmation?: Specify whether the
ASCII name is verified when a subscriber sends a message using NameNet. If the
name does not match, the Message Networking system requests an update. Select
yes to verify the ASCII name. Select no if you do not want to
verify the ASCII name. The default for this field is yes.
Admin Mode?: Specify that when Message Networking
delivers a message to a remote machine using the Octel Analog Networking gateway,
Message Networking automatically requests a subscriber update for the receiving
subscriber. Select yes to automatically request a subscriber update.
Select no if you do not want to automatically request a subscriber update.
The default for this field is no.
Octel Analog Serial Number: Type the serial
number of the analog remote machine, either 4 or 5 digits.
Dynamic Sub Expiration Days: Type
the number of days a dynamically-added subscriber can exist without
performing any activity (without sending or receiving messages).
This number must match the Maximum Number of Days for NameNet Records
field on the Octel 100 system. The default for this field is 90.
The minimum for this field is 1. The maximum for this field is 999.
Record Delay (Sec): The Record
Delay is a timing parameter used by the Octel Analog Networking
protocol that specifies the number of seconds before recording
begins. The default for this field is 3. If clipping occurs at
the beginning of a message received by an Octel Analog Networking
remote subscriber, increase this value to eliminate clipping.
If silence occurs at the beginning of a message received by an
Octel Analog Networking remote subscriber, decrease this value
to eliminate the silence.
Maximum Simultaneous Connections: Maximum number
of ports that will simultaneously handle outgoing traffic for this machine.
Enter an integer of 1 through 9 The default for this field is 1.
Voiced Name Delay (Sec): The Voiced Name Delay
is a timing parameter used by the Octel Analog Networking protocol that specifies
the number of seconds before a remote subscriber's name is voiced. The default
for this field is 3. If clipping occurs at the beginning of a message received
by an Octel Analog Networking remote subscriber, increase this value to eliminate
clipping. If silence occurs at the beginning of a message received by an Octel
Analog Networking remote subscriber, decrease this value to eliminate the silence.
Note:
The default Voiced Name Delay for the Octel 100 is 2 seconds.
System Mailbox ID: This field specifies
the system mailbox number used by the protocol for the remote machine,
up to 10 digits. The default for this field is 0. This mailbox address
must match the system mailbox set up on the remote machine.
If you are modifying an existing machine, click Save to
save your changes. If you are adding a new machine, click Next
Step to save the remote machine and administer
Dial Plan Mapping, or click Add this Machine if you do
not want to administer Dial Plan Mapping at this time:
- If you click Next Step, the Administer Dial Plan Mapping
page displays.
- If you click Add this Machine, a message displays that
the parameters have been saved. Click OK.
Top of page
|
