Correct speed dial code needs to be used for this system.System speed dial numbers for basic partner needs to be programmed correctly.System speed dial for Partner Plus/II (R1-R3.1) needs to be programmed correctly.System speed dial for Partner Plus/II (R4.0& R4.1) and all Partner ACS/PES needs to be programmed correctly.
System and Release (F#1, F59) not using the correct speed dial codes for this system
Some Partner Systems use a 2-digit System Speed dial code while others use a 3-digit code. If you try to program a code that does not belong to that system, you will get an error when trying to program. Use the attachments to verify System and Release and the feature comparison chart to verify if the code is 2 or 3-digits.
Note: The Feature Comparison chart (Refer to the attached document 'feature comparison') will show the number of System Speed Dials available for that system. If the number is less than 100, it uses a 2-digit code. If the number is 100 or greater, it uses a 3-digit code.
To identify the Partner system use the attached Partner Beep Chart.
System speed dial Numbers for Basic Partner programmed incorrectly
System Speed Dial is available for all Partner systems.
Description:
System Speed Dialing allows you to store outside numbers (up to 20 digits), in the system's memory. Once you store the numbers, any user can dial them automatically by pressing Feature and a two-digit code. The quantity of numbers that can be stored depends on the Partner Release.
PR1 .............................................. 10 entries (20 - 29).
PR2, PR3, P31, PR4, P41 ............ 60 entries (20 - 79).
NOTE: If the user/technician has trouble programming System Speed Dial, and they are used to programming another release of Partner, they may experience some problems due to these differences:
- Basic Partner and Partner Plus/II R1-R3.1 use only two digits (20-79).
- Partner Plus/II R4.0 & R4.1 and Partner ACS/PES use three digits (600-699).
- Basic Partner and Partner Plus/II R1-R3.1 allow only 20 digits.
- Partner Plus/II R4.0 & R4.1 and Partner ACS/PES allow up to 28 digits.
How to Program:
From extension 10
- Press Feature 00.
- Press Feature and dial a 2 digit code (PR1: 20-29) (PR2 or higher: 20-79).
- Dial the phone number (up to 20 digits).
- To store another number, go to step 2 or to exit Press Feature 00.
Note: Special Dialing Functions:
You can enter the following special functions in Speed Dial or Auto Dial numbers:
|
Function
|
Button
|
Display
|
Description
|
|
Pause
|
Hold
|
P
|
1.5-second pause
|
|
Recall
|
Spkr
|
R
|
Timed switchhook flash
|
|
Stop
|
Mic
|
S
|
Stops dialing sequence until button is pressed or code is dialed again
|
|
Touch-Tone Enable
|
Transfer
|
T
|
Sends touch-tones over a rotary line
|
How to use:
System Phone:
- Lift the handset. You hear the intercom dial tone.
- Press Feature (or # from a single line phone) and the 2-digit Speed Dial code.
Single Line phone:
- Lift handset, you hear intercom dial tone.
-
Press: # and the 2-digit Speed Dial code, the system will access an outside line and dial the speed dial number.
System Speed Dial for Partner Plus/II (R1-R3.1) programmed incorrectly
System Speed Dial is available on All Partner Systems
Description:
This Feature lets you programa list of up to 60 frequently dialed numbers for the system. Anyone on the system can then dial a System Speed Dial number by pressing Feature (or # on a Standard Phone) and the two-digit code 20-79.
NOTE: If the user/technician has trouble programming System Speed Dial, and they are used to programming another release of Partner, they may experience some problems due to these differences:
- Basic Partner and Partner Plus/II R1-R3.1: Use only two digits (20-79).
- Partner Plus/II R4.0 & R4.1 and Partner ACS/Endeavor: Use three digits (600-699).
- Basic Partner and Partner Plus/II R1-R3.1 allow only 20 digits.
- Partner Plus/II R4.0 & R4.1 and Partner ACS/Endeavor allow up to 28 digits.
How to Program:
From extension 10 or 11 (10 only on PP1 & PP2):
- Press: Feature 00.
- Press: Feature (2 digit code 20-79).
(Optional) To mark the Speed Dial number to override dialing restrictions, precede the phone number by a *.
- Dial: Phone number up to 20 digits.
- To enter another number go to step 2 or Press Feature 00 to exit programming.
Special Dialing Functions:
You can enter the following special functions in Speed Dial or Auto Dial numbers:
|
Function
|
Button
|
Display
|
Description
|
|
Pause
|
Hold
|
P
|
1.5-second pause
|
|
Recall
|
Spkr
|
R
|
Timed switchhook flash
|
|
Stop
|
Mic
|
S
|
Stops dialing sequence until button is pressed or code is dialed again
|
|
Touch-Tone Enable
|
Transfer
|
T
|
Sends touch-tones over a rotary line
|
Overriding restrictions:
System phones can use a wildcard * before the number to override certain restrictions. Also, Standard Phone users or MDW phone users can use a marked system speed dial to override restrictions since they are unable to use the Password Feature. Enter a * by itself to override all local and long distance; or * followed by phone number to allow certain phone numbers only.
System Speed Dial for Partner Plus/II (R4.0 & R4.1) and all Partner ACS/PES programmed incorrectly
System Speed Dial is available on all Partner Systems
This Feature lets you program a list of up to 100 frequently dialed numbers for the system. Anyone on the system can then dial a System Speed Dial number by pressing (Feature) (or (#) on a Standard Phone) and the three-digit code (600-699).
NOTE: If the user/technician has trouble programming System Speed Dial, and they are used to programming another release of Partner, they may experience some problems due to these differences:
- Basic Partner and Partner Plus/II R1-R3.1 use only two digits (20-79)
- Partner Plus/II R4.0 & R4.1 and Partner ACS/PES use three digits (600-699)
- Basic Partner and Partner Plus/II R1-R3.1 allow only 20 digits.
- Partner Plus/II R4.0 & R4.1 and Partner ACS/PES allow up to 28 digits.
How to Program:
- Fromextension 10 or 11, Press Feature 00.
- Press Feature (3 digit code 600-699).
(Optional) To mark the Speed Dial number to override dialing restrictions, enter a * as the first digit before step 3.
- Dial the Phone number (up to 28 digits).
- To enter another number go to step 2.
- Press Feature 00 to exit programming
Note: Special Dialing Functions
You can enter the following special functions in Speed Dial or Auto Dial numbers:
|
Function
|
Button
|
Display
|
Description
|
|
Pause
|
Hold
|
P
|
1.5-second pause
|
|
Recall
|
Spkr
|
R
|
Timed switchhook flash
|
|
Stop
|
Mic
|
S
|
Stops dialing sequence until button is pressed or code is dialed again
|
|
Touch-Tone Enable
|
Transfer
|
T
|
Sends touch-tones over a rotary line
|
To Remove System Speed Dial Number:
- From extension 10 or 11, press: Feature 00.
- Press Feature and a 3 digit code (600-699).
- Press: Mic.
- To remove another Speed Dial number, go to step 2.
- Press Feature 00 to exit programming mode.
