Task List to Install a New G700 with an S8700 (No Local Survivable Processor)

Task List to Install a New G700 with an S8700 (No Local Survivable Processor)

Use the following checklist to install a G700 Media Gateway with the following characteristics:

The G700 is controlled exclusively by an external S8700 Media Server.

Table 4. Task List to Install a New G700 with an S8700 (No Local Survivable Processor) �
Task	Subtasks (If any)
Get Planning Forms from the Project Manager
Get the Serial Number of the G700
Set Up the TFTP Server on Your Laptop or on a Customer PC
Download the tar.gz File from CD-ROM to Your TFTP Directory and Unzip It	Download the tar.gz File from CD-ROM to Your TFTP Directory and Unzip It or Download the Firmware Files from the Web to Your TFTP Directory
Perform Environmental Verification
Perform Power Verification
Perform Grounding Verification
Unpack and Check the Order
Prepare the G700 Media Gateway	Affix Mounting Brackets to the G700 or Affix Feet on the Table-Top G700
Mount the G700 Media Gateway in the Rack
Insert the Avaya S8300 Media Server (If Necessary for Standalone Service or LSP)
Insert the Media Modules
Insert an Avaya Expansion Module
Insert an Avaya X330STK Stacking Module
Cable Multiple Units	Connect Units within a Single Stack
	Link Elements in Multiple Racks
Attach Ground Conductors	Review General Grounding Requirements and Approved Grounds
	Connect the Safety Ground
Connect AC Power	Review Power Requirements
	Test the AC Outlet
	Plug in AC Power
Prepare to Configure the G700 Media Gateway	Review Physical Access Methods
	Connect Your Laptop to the G700 Serial Port
	Log in to the Avaya P330 (Layer 2 Switching Processor) Command Line Interface
	Determine Necessary Firmware to Install on the G700
Assign the IP Addresses of the G700 Media Gateway Components	Assign the IP Address to the P330 Stack Processor (Layer 2 Switching Processor)
	Establish the IP Routing for the Stack
	Check the Serial Number of the G700 Media Gateway Processor
	Assign the IP Address to the G700 Media Gateway Processor
	Assign the Default IP Route to the G700 Media Gateway
	Assign IP Addresses to the VoIP Resources
Configure an X330 Expansion Module (If Necessary)
Check for IP Connections
Set up a laptop for a direct Ethernet connection (If Necessary for Firmware Download)	Check Your Version of Windows
	Change TCP/IP Properties and Network Settings (Windows 2000 and XP) or Change TCP/IP properties (Windows 95, 98, NT 4.0, and Millennium Edition [Me])
	Disable proxies in browser
	Verify That the tftpboot Directory Has the Right Firmware Versions
Install New Firmware on the G700 Media Gateway	Connect Laptop to the Customer's LAN (If Laptop Has the TFTP Server)
	Install New Firmware on the P330 Stack Processor (Layer 2 Switching Processor)
	Install New Firmware Files on the G700 Media Gateway Processor
	Install New Firmware on the Media Modules
	Set SNMP Traps
	Set up the Controller List for the G700 Media Gateway
	Configure Other G700 Media Gateways (Stack Configuration)
	Configure Other G700 Media Gateways (Remote, No Stack Configuration)
Administer MultiVantage Software on the S8700	Log in to the S8700 MultiVantage SAT Screens
	Assign the S8700's CLAN Node Name and IP Address NOTE: This assignment should have already been established as a part of normal S8700 installation.
	Define the IP Network Regions for the G700 Media Gateway and the S8700 CLAN Board(s) NOTE: This definition should have already been established as a part of normal S8700 installation.
	Define the IP Interfaces of the S8700 Port Network CLAN Boards NOTE: This definition should have already been established as a part of normal S8700 installation.
	Add Media Gateways
	Verify Changes
	Enable Announcements, If Necessary
	Save MultiVantage Translations
Complete the Installation Process